User Guide Manual

6-3System 5 IP Switchers • Special Applications
Using IRCM control modules for DVD-VCR control
The output of a combination DVD-VCR player can be connected to a single input of
the System 5 IP, and you can install and configure Extron control modules such as
the IRCM-DVD or IRCM-DVD+, and an IRCM-VCR to control the separate sources
within the combination device.
PC
DOC
CAM
VCR
PIC
MUTE
ON OFF
MENU NEXT
AUTO
IMAGE
DVD
LAPTOP
23 4
5/ PC
DISPLAY
1
INPUT SELECTION
CONFIG
IR
100-240V 1.3A
50-60Hz
Tx
Rx
G
G
S
G
S
G
S
Ps
+V
R
Y/C
G
Y
B
VH
VID
Y/C
VID
CY
R/VID G/Y B/C
H
V
C
VID
VH
R/VID
G/Y B/C
INPUT 1
INPUT 3
INPUT 4
INPUT 2
RS-232
PROJ CONT
AUDI O
IR/SERIAL
L 1 R
L 2 R
OUTPUT
A
L
B
C
OUTPUT
DVD-VCR Player
IRCM-VCR IRCM-DVD
System 5 IP
DVD CONTROL
REW PLAY NEXT PAUSE STOP
Tx
VCR CONTROL
REW PLAY FWD PAUSE STOP
Tx
Using an IRCM-DV+ control module for DVD-VCR control
If the combination DVD-VCR player has only one available output port and neither
a distribution amplifier nor a pair of control modules [(IRCM-DVD or
IRCM-DVD+) and IRCM-VCR] is available for use, you can create a special
switcher configuration to allow control via the System 5 IP or SCP front panel and
an optional IRCM-DV+.
100-240V 1.3A
50-60Hz
Tx
Rx
G
G
S
G
S
G
S
Ps
+V
R
Y/C
G
Y
B
VH
VID
Y/C
VID
CY
R/VID G/Y B/C
H
V
C
VID
VH
R/VID
G/Y B/C
INPUT 1
INPUT 3
INPUT 4
INPUT 2
RS-232
PROJ CONT
AUDI O
IR/SERIAL
L 1 R
L 2 R
OUTPUT
A
L
B
C
OUTPUT
DVD-VCR Player
IRCM-DV+
System 5 IP
PC
DOC
CAM
VCR
PIC
MUTE
AUTO
IMAGE
ON OFF
MENU NEXT
DVD
LAPTOP
23 4
5/ PC
DISPLAY
1
INPUT SELECTION
CONFIG
IR
DVD & VCR CONTROL
PLAY NEXT/FWD PAUSE STOP
TUNER
Tx
PREV/REW
ENTER
TITLE MENU
TV/VCR
DVD VCR
An IRCM-DV+ normally must be associated with two different inputs, one for the
DVD half, one for the VCR half of the IRCM-DV+. In order to use an IRCM-DV+ in
this installation, both halves must be associated with the same input.
In this example (shown above and described in the following procedure), the
DVD/VCR player’s output is connected to switcher input 3. Room/function
button 2 will be configured to associate both the DVD and VCR halves of the
IRCM-DV+ with input 3. It will also be configured to select between the DVD and
VCR halves of the IRCM-DV+.
Detailed instructions on basic configuration via Global Configurator software
are available in the System 5 IP Setup Guide.
The numbers in the sample screen shown below correspond to the procedure’s
step numbers.