User Guide Manual
5-9System 5 IP • SIS
™
Programming and Control
PRELIMINARY
Command/response table for SIS commands (continued)
Command ASCII (Telnet) URL Encoded (Web) Response Additional description
(host to switcher) (host to switcher) (switcher to host)
Video configuration
Select the video input signal type
24
X200
*
X201
\
X200
%2A
X201
%5C Inp
X200
•Typ =
X201
Set input signal type for input
X200
where
X201
= 1 (RGB) or 2 (Vid).
Example: 2*2\ 2%2A2%5C Inp02•Typ=2
Example: set input 2 to S-video or composite
video.
Video output may turn off briefly (for the duration of the RGB delay setting) while you set the video configuration for inputs 1 and 2 or when you press the Menu and Next
buttons and enter the Video Config menu, whether or not you make any changes to the configuration.
View the video signal type
X200
\
X200
%5C
X201
Show the video signal type.
Example:2\2%5C1
Example: show input 2’s video type.
Audio gain/attenuation (per input)
Set a specific input’s audio gain
24
X200
*
X202
G
X200
%2A
X202
G Inp
X200
• Aud=
X204
dB Set input
X200
’s gain in decibels
(
X202
= between 0 dB and 30 dB in 1 dB
steps).
X204
= audio gain or attenuation
(-40 dB to +30 dB in 1 dB steps). This
command is case-sensitive.
Example: 5*9G 5%2A9G Inp05•Aud=+09dB
Example: set input 5’s gain to +9 dB.
Set a specific input’s attenuation
24
X200
*
X203
g
X200
%2A
X203
g Inp
X200
•Aud=
X204
dB Set an input’s attenuation (
X203
= -1 dB to
-40 dB in 1 dB steps). Case-sensitive.
Example: 4*12g 4%2A12g Inp04•Aud=-12dB
Example: set input 4’s attenuation to -12 dB.
Increment a specific input’s level
24
X200
*+G
X200
%2A%2BG Inp
X200
•Aud=
X204
dB Increase an input’s gain by 1 dB.
Decrement a specific input’s level
24
X200
*-G
X200
%2A%2DG Inp
X200
•Aud=
X204
dB Decrease an input’s gain by 1 dB.
View a specific input’s audio level
X200
*G
X200
%2AG
X204
Show an input’s audio level.
Set current input’s audio gain
24
X202
G
X202
G Inp
X200
•Aud=
X204
dB Set the current input’s gain (in dB). This
command is case-sensitive
Set current input’s audio attenuation
24
X203
g
X203
g Inp
X200
•Aud=
X204
dB Set attenuation (in dB). This command is
case-sensitive.
Increment current input’s gain
24
+G %2BG Inp
X200
•Aud=
X204
dB Increase the gain by 1 dB.
Decrement current input’s gain
24
-G %2DG Inp
X200
•Aud=
X204
dB Decrease the gain by 1 dB.
View current input’s audio gain G G
X204
Show the audio level.
Volume adjustment (overall: amp and preamp outputs)
Set the overall output volume
X8
V
X8
V Vol
X8
Specify the volume (0-40) for audio output.
Example: 27V 27V Vol027
Example: set volume to 27.
Increment the volume +V %2BV Vol
X8
Increase audio output.
Decrement the volume -V %2DV Vol
X8
Decrease audio output.
View the volume level V V
X8
Show the output volume.