Operating instructions

Programmer’s Guide, cont’d
CrossPoint Plus Matrix Switchers • Programmer’s Guide4-4
Command/Response Table
Symbol Definitions:
= Carriage return/line feed
= Carriage return (no line feed)
• = space
X1
= Input number 01 – 08 (CrossPoint Plus 84, 88);
01 – 12 (CrossPoint Plus 124, 128);
01 – 16 (CrossPoint Plus 168, 1616)
X2
= Output number 01 – 04 (CrossPoint Plus 84, 124);
01 – 08 (CrossPoint Plus 88, 128, 168);
01 – 16 (CrossPoint Plus 1616)
X3
= Input number (for tie) 0 – maximum number of inputs (0=disconnected)
X4
= Frequency xxx.xx (frequency in Hz (vertical) or kHz (horizontal))
X5
= Group 0 – 4 (0 = not assigned to a group)
X6
= RGB delay 0 – 10 (0 to 5 seconds, 0.5 seconds/step)
X7
= Audio gain 0 – 9 (1dB/step)
X8
= Audio attenuation 1 – 15 (1dB/step)
X9
= Numeric dB value -15 to +09
Xa
= Preset number 00 – 16 (0 = current configuration)
Xb
= Preset number 01 – 16
Xc
= Executive mode 1 = on;
0 = off
Xd
= Controller software version number to second decimal place
Command/response table for SIS commands
Command ASCII Command Response Additional description
(host to switcher) (switcher to host)
Create ties
Tie input
X3
to output
X2
, A & V
X3
*
X2
! Out
X2
•In
X3
•All
Example: 1*3! Out03 •In01•All Tie input 1 A & V to output 3.
Tie input to output, RGBHV only
X3
*
X2
& Out
X2
In
X3
RGB Audio breakaway.
Example
1
: 10*4& Out04•In10•RGB Tie input 10 RGB to output 4.
Tie input
X3
to output
X2
, video only
X3
*
X2
% Out
X2
In
X3
Vid Audio breakaway.
Example
1
: 7*5% Out05•In07•Vid Tie input 7 video to output 5.
Tie input
X3
to output
X2
, audio only
X3
*
X2
$ Out
X2
•In
X3
Aud Audio breakaway.
Example: 12*8$ Out08•In12•Aud Tie input 12 audio to output 8.
Quick multiple tie
Esc
Q
X3
*
X2
!…
X3
*
X2
! Out Multi In Multi All
Example:
Esc
Q3*4!3*5!3*6! Out Multi In Multi All Tie input 3 to outputs 4, 5, and 6.
Tie input to all outputs
X3
! Out Multi In
X3
All
Example: 5! Out Multi In 05 All Tie input 5 to all outputs.
Digital Sync Validation Processing
List individual sync (DSVP)
X1
LS In
X1
•Hrz=
X4
•Vrt=
X4
Example: 2LS In02•Hrz=031.50•Vrt=060.00 Input 2 frequency is 31.5 kHz
horizontal and 60 Hz vertical
1
The & tie command for RGB and the % tie command for video can be used interchangeably on the CrossPoint Plus
models.
Input and output numbers in
commands may be entered as
either 1-digit or 2-digit
numbers. All input and
output numbers are specified
as 2-digit numbers in the
response.