User guide

SMX System MultiMatrix Switcher • SIS Configuration and Control 49
Command ASCII Command
(Host to Switcher)
Response
(Switcher to Host)
Additional Description
Commands Specific to SMX SDI/HD-SDI Boards
Output Re-clocking Per Slot
Set output reclocker per slot
X3)*X#*X1*= RteX3)*X#*X1*]
Read reclocker
X3)*X#= X1*]
List DSVP (Digital Sync Validation Processing)
DSVP for VGA and RGBHV
List individual sync (DVSP)
X3)*X!LS
X1%
H
,X1%
V
]
X3)FRQX!
1
,X1%
H
,X1%
V
]
Listed as Horizontal, Vertical.
Verbose mode 2 or 3
NOTE: Unit responds 0000.00, 0000.00 if no connection or an error is found.
List all input sync (DVSP)
X3)*0LS
X1(
1
X1(
2
... X1(
n
]
X3)FRQ00*X1(
1
X1(
2
... X1(
n
] Verbose mode 2 or 3
DSVP (Signal Present) for Composite/S-video/DVI/DVI-Pro/HDMI Boards
List all input sync (DVSP)
X3)*0LS
X1(
1
X1(
2
... X1(
n
]
X3)FRQ0*X1(
1
X1(
2
... X1(
n
] Verbose mode 2 or 3
NOTE: List individual signal present per slot is not available on this board. Unit responds with error E14.
DSVP (Signal Present and Rate/Reclocker) for SDI/HD-SDI Boards
List individual sync (DVSP)/slot
X3)*X#LS X1)]
X3)FRQX#*X1)] Verbose mode 2 or 3
NOTE: Unit responds 0000 if no connection, no ties, or an error is found.
List all sync (DVSP)/slot
X3)*0LS
X1(
1
X1(
2
... X1(
n
]
X3)FRQ0*X1(
1
X1(
2
... X1(
n
] Verbose mode 2 or 3
DSVP (Link Present) for Fiber Optic Boards
List all input (DVSP)
X3)*0LS
X1(
1
X1(
2
... X1(
n
]
X3)FRQ0*X1(
1
X1(
2
... X1(
n
] Verbose mode 2 or 3
NOTE: List individual signal present per slot is not available on this board. Unit responds with error E14.
Fiber Optic Board Status
View Fiber transceiver module
installed
0*
X3)I
X*
1
X*
2
... X*
n
]
InfX3)*X*
1
X*
2
... X*
n
] Verbose mode 2 or 3
NOTES:
X! = Input number 01 - <maximum number of inputs>
X# = Output Number 01 - <maximum number of outputs>
X* = Fiber optic transceiver module 0 = no module installed
1 = multimode module
2 = singlemode module
X1) = Output rate ---- = bypass mode
0000 = no connection (rate mismatch)
nnnn = actual rate
X1% = Sync frequency xxx.xx in Hz or kHz
X1* = Reclocker rates for SDI/HD-SDI board 00 = autodetect (default)
01 = bypass the reclocker
X1( = Signal status where 0 = no signal at input
1 = signal at input (H sync)
2 = signal at input (V sync)
3 = signal at input (H and V sync) or receive link presence
X3) = Slot address 01 - 10