User's Guide MLM-UDSM MediaLink™ Under Desk Slide Mount Mounting Option 68-628-01 Rev.
Precautions Safety Instructions • English I D Power sources • This equipment should be operated only from the power source indicated on the product. This equipment is intended to be used with a main power system with a grounded (neutral) conductor. The third (grounding) pin is a safety feature, do not attempt to bypass or disable it. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock.
MLM-UDSM Installation Guide About the MLM-UDSM The Extron MLM-UDSM is an under desk/table mounting enclosure for the MediaLink™ Controller (MLC 206) that provides a way to slide the MLC out of the way (like closing a drawer) when not in use. The MLM-UDSM also provides four single-space Architectural Adapter Plate (AAP) openings for attaching control modules or other AAP devices. It is available in three colors: gray (Extron Part #60-394-01), black (#60-394-02), and white (#60-394-03).
MLM-UDSM Installation Guide, cont’d Install the MLC and AAP accessories in the sliding enclosure 1. Set the sliding enclosure’s top plate on the table/desk. 2. If applicable, set the DIP switches on any AAP devices to be attached to the MLM-UDSM. 3. Attach AAP plates or AAP devices: insert the AAP plate’s or device’s screws through the holes in the MLM-UDSM’s AAP mounting area, as shown at right.
7. Replace or add labels, if needed. Refer to the MediaLink Controllers User’s Manual for instructions. 8. Turn the MLM-UDSM sliding enclosure’s top plate right side up. 9. Align the openings in the sliding enclosure’s top plate with the controller’s buttons, knob, and LEDs, and place the top plate on the MLC as shown below. 10. As shown below, insert the four screws removed in step 5, and tighten them to secure the MLC to the MLM-UDSM sliding enclosure’s top plate.
MLM-UDSM Installation Guide, cont’d 14. Lower the sliding enclosure’s top panel (with attached MLC and AAP accessories) onto the bottom panel, and align the screw holes. The cables should be routed to the rear of the enclosure. 15. Insert and fasten the eight screws that connect the top and bottom of the sliding enclosure, and fasten them securely. See the illustration below.
Insert and tighten the two screws on either side of the mounting plate. These screws prevent you from pulling the sliding drawer completely out from the mounting plate. M ed ia L in k 2.
MLM-UDSM Installation Guide, cont’d MLM-UDSM Dimensions 9 in che hes c 3 in s M ed ia L in k 1 Shelf fully extended to 4.17 inches Ex tro n Tx L RO NT D DV CO E US PA OP ST XT NE AY PL W RE 2.25 inches 9.000 8.000 7.212 0.213 THRU (2 places) 2.645 1.000 .500 .000 .880 .000 .330 12.990 11.900 12.400 .000 .500 1.000 .000 0.174 THRU (6 places) .000 .880 12.720 .270 2.250 N All dimensions are in inches.
Extron’s Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase.
www.extron.com Extron Electronics, USA Extron Electronics, Europe Extron Electronics, Asia Extron Electronics, Japan 1230 South Lewis Street Anaheim, CA 92805 USA 714.491.1500 Fax 714.491.1517 Beeldschermweg 6C 3821 AH Amersfoort The Netherlands +31.33.453.4040 Fax +31.33.453.4050 135 Joo Seng Road, #04-01 PM Industrial Building Singapore 368363 +65.6383.4400 Fax +65.6383.4664 Kyodo Building 16 Ichibancho Chiyoda-ku, Tokyo 102-0082 Japan +81.3.3511.7655 Fax +81.3.3511.
