Installation Guide ISS 506 I/O Boards Optional Input and Output Board Installation www.extron.com Extron Electronics, USA 1230 South Lewis Street Anaheim, CA 92805 800.633.9876 714.491.1500 FAX 714.491.1517 Extron Electronics, Europe Beeldschermweg 6C 3821 AH Amersfoort, The Netherlands +800.3987.6673 +31.33.453.4040 FAX +31.33.453.4050 Extron Electronics, Asia 135 Joo Seng Rd. #04-01 PM Industrial Bldg., Singapore 368363 +800.7339.8766 +65.6383.4400 FAX +65.6383.4664 © 2007 Extron Electronics.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
Installation The ISS 506 can be modified to install or remove optional boards that change the input and/or output formats that the switcher can process.
Installation, cont’d 3. Remove the 14 screws, 8 on the top and 3 on each side of the ISS cover (figure 1). Remove (14) screws from top and sides. Lift cover straight up.
Installation, cont’d 4. Lift the top cover straight up approximately five inches until you can access the fan power cord. C Do not touch any electronic components inside the ISS. Doing so could damage the switcher. Electrostatic discharge (ESD) can damage IC chips even though you cannot feel it. You must be electrically grounded before proceeding with maintenance. A grounding wrist strap is recommended. 5. Disconnect the fan power cord from connector J46 on the main board. 6.
Installation, cont’d 2. On the main board (figure 2), locate connectors J26, J43, and J44 (a); the three standoffs (b); and the rear panel connector port (c). 2 3 1 J26 2 2 1 J43 1 J44 Figure 2 — SDI/HD-SDI input board installation location 3. From the inside of the switcher, pop the cover out of the rear panel connector port (c).
Installation, cont’d 4. See figure 3. Tip the input board up and guide its output connector through the rear panel connector port (d). 5 5 4 5 Figure 3 — Input board installation 5. See figure 3, above. Align the connectors on the main board and board (e). Gently apply pressure to carefully mate the input board with the main board.
Installation, cont’d 6. See figure 4. Secure the board to the standoffs on the main board with the three included screws (f).
Installation, cont’d 7. Secure the board to the back panel with the included hex nut (figure 5). UT Y TP NV CO AN C U DO TE ER VID SC / B-Y B Y/ G / R-Y R 2 23 RS IEW -Y EV , B PR -Y, Y B/R RG M RA OG PR G /Y I SD VID VID /Y 6 B-Y /C S R R-Y O U T P U YC T S L D FIXE SE RE T B-Y R L M LE RIAB VA N IEW EV PR V RA H OG PR L Y, -Y, B/R RG B/ B-Y LA 2 /42 R R R-Y L 6 R Figure 5 — Secure the board to the rear panel 8. Close and reinstall the switcher.
Installation, cont’d 1. Open the switcher. See “Opening the Switcher” on page 1. C 2. Do not touch any switches or other electronic components inside the ISS. Doing so could damage the ISS. Electrostatic discharge (ESD) can damage IC chips even though you cannot feel it. You must be electrically grounded before proceeding with any electronic component replacement. A grounding wrist strap is recommended.
Installation, cont’d 4 2 J2A J2B 3 2 J1 Figure 7 — Output board installation location ISS 506 Optional I/O board • Installation
Installation, cont’d N The HD-SDI and low resolution (scan converter) output boards use connectors J2A/J2B and J1. The DVI output board uses J2A/J2B only. 4. Align one or both connector extension(s) with J1 and J2A/J2B on the main board (e). Gently apply pressure to carefully mate the extension(s) with the main board (figure 8). N To make installation of the board easier, angle the extensions slightly away from the rear of the ISS as shown.
Installation, cont’d 5. See figure 9. Align the connector(s) on the board with those on the extension(s) (f). Gently apply pressure to carefully mate the output board with the main board.
Installation, cont’d 6. See figure 10. Continue to apply presure until the connector extension(s) are fully mated with the main board (g). Mated connectors are straight on the top and bottom of the connector extension. 7 7 Figure 10 — Output board installation N Ensure that each contact on the connector extension(s) is properly mated with the output board, and not shifted to the front or rear. If the board’s rear panel is not flush with the ISS’s rear panel, the board is probably not properly mated.
Installation, cont’d 8 Figure 11 — Secure the output board to the standoff ISS 506 Optional I/O board • Installation 13
Installation, cont’d 8. Secure the output board to the back panel with the two screws (i) removed in step 2 (figure 12). 9 9 LORES OUT C VID R-Y/ R Y/ G LAN Y B-Y/ B RS232/422 RESET Figure 12 — Secure the output board to the rear panel 9. Close and reinstall the switcher. See “Closing the Switcher”, below. Closing the Switcher 1. Reconnect the fan power cord to connector J46 on the main board. 2. Replace the top cover on the ISS. 3.
