User Manual

Extron USA - West
Headquarters
+800.633.9 876
Inside USA / Canada Only
+1.714.491.15 00
+1.714.491.1517 FAX
Extron USA - East
+800.633.9 876
Inside USA / Canada Only
+1.919.8 63.1794
+1.919.8 63.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.404 0
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.88 3.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299180 0
+971.4.299188 0 FA X
68-1123-63
Rev A
08 10
© 2010 Extron Electronics. All rights reserved. www.extron.com
4
ISM VS Output Board • Setup Guide, cont’d
NOTE: X! = Input number, 0-8
X@ = Output number, 1-8
X1) = Mode status, 1 = on, 0 = off
X1% = Picture adjustment (0 to 255)
X2! = Output resolution, 01 = 640x480, 02 = 800x600, 03 = 852x480, 04 = 1024x768,
07 = 1280x768, 08 = 1280x1024, 09 = 1360x765, 10 = 1365x768, 11 = 1366x768,
12 = 1365x1024, 13 = 1400x1050, 15 = 480p, 16 = 576p, 17 = 720p,18 = 1080i,19 = 1080p
X2@ = Refresh rate, 1 = 50 Hz, 2 = 60 Hz
X2% = User presets (1 to 3)
Board-specific SIS commands table
Command ASCII
command
(host to ISM)
Response
(ISM to host)
Additional description
Input selection
Video and audio
X!*X@! OutX@•InX!•All
]
Tie video/audio input X! to X@.
Video
X!*X@& OutX@•InX!•RGB
]
Tie video input X! to output X@.
Audio
X!*X@$ OutX@•InX!•Aud
]
Tie audio input X! to output X@.
Output scaler rate
Set output rate
X@
*
X2!
*
X2@
= RteX@ *X2!*X2@
]
Set output resolution/refresh rate
View
X@
= X2!*X2@
]
View resolution/refresh rate
User presets (1 to 3)
Recall preset
X@*X2%.
X@
Rpr
X2%]
Recalls user preset
X2%
.
Save preset
X@*X2%,
X@
Spr
X2%]
Saves user preset
X2%
.
Edge smoothing filter
Set filter on/off
16*X@*X1)# X@
Fil
X! *X1)]
Set filter on or off.
View setting
16*X@#
X1)]
View setting.
Enhancement mode
Set mode on/off
52*X@*X1)# X@
Ehn
X! *X1)]
Set enhancement mode on or off.
View setting
52*X@#
X1)]
View setting.
Top blanking
Specify a value
X@*X1% ( X@
Blt
X!*X1%]
Set number of top lines to blank.
Increment value
X@+( X@
Blt
X!*X1%]
Increase number of lines to blank.
Decrement value
X@-( X@
Blt
X!*X1%]
Decrease number of lines to blank.
View
X@(
X1%]
Show number of lines to blank.
Bottom blanking
Specify a value
X@*X1% ) X@
Blb
X!*X1%]
Set number of bottom lines to
blank.
Increment value
X@+) X@
Blb
X!*X1%]
Increase number of lines to blank.
Decrement value
X@-) X@
Blb
X!*X1%]
Decrease number of lines to blank.
View
X@)
X1%]
Show number of lines to blank.