User’s Manual Infrared Remote Control www.extron.com Extron Electronics, USA 1230 South Lewis Street Anaheim, CA 92805 800.633.9876 714.491.1500 FAX 714.491.1517 Extron Electronics, Europe Beeldschermweg 6C 3821 AH Amersfoort, The Netherlands +800.3987.6673 +31.33.453.4040 FAX +31.33.453.4050 Extron Electronics, Asia 135 Joo Seng Rd. #04-01 PM Industrial Bldg., Singapore 368363 +800.7339.8766 +65.6383.4400 FAX +65.6383.4664 © 2006 Extron Electronics. All rights reserved.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
ᅝܼ乏ⶹ • Ё᭛ 䄺ਞ 䖭Ͼヺোᦤ⼎⫼᠋䆹䆒⫼᠋ݠЁ ᳝䞡㽕ⱘ᪡㓈ᡸ䇈ᯢDŽ ⬉⑤ • 嬦 嫿 ⡈ ⌫ 倾 Ề 䑩 ᷨ ␂ ᵋ 㝈 㕏 䗅 䑶 㷑 ɿ 嫿 ⡈ ⼆枼Ề䑩㙊♱一䗅Ờ䑶䰼丠Ờ䑶ɿ 䩭ᵊ㚢一 澠♱一澡㕰⫊₩嫿㓾澤ᵎ倾ᵎ䑩ㅗ崴弈ɿ 䖭Ͼヺো䄺ਞ⫼᠋䆹䆒ᴎݙ᳝ᲈ ᢨᥝ⬉⑤ • ᵻ⫊₩♱ḏ嫿⡈㈕㋊䑶㷑澤嬸㈕㋊ㆁ㙊嫿⡈⍏ ㅗ㞍暣䑶㷑䗅䑶㷑一澤ㅗḼẖ㋦ⅱⵃ䑶䰼丠䗅䑶㷑一ɿ 䴆ⱘॅ䰽⬉य़ˈ᳝㾺⬉ॅ䰽DŽ ⬉⑤㒓ֱᡸ • ⣦Ⓟⵄ一澤 忀₎埬嵪嵐澤ㅗ愎䆪㉥⋌ɿ ⊼ᛣ 䯙䇏䇈ᯢк • 䑩 ㅸ Ề 䑩 嬦 嫿 ⡈ ⼆ 枼 敆 嬼 䍇 夤ㆁ㙊⫊₩⏍Ề䑩嬵㕏ɿ ֱᄬ䇈ᯢк • 䑩ㅸⷕ⪙⫊₩嬵㕏ᶧḦ⡈⭇㚦Ề 䑩ɿ 䙉ᅜ䄺ਞ • 䑩ㅸⷕ徶⫉ᷨ␂⏍䑩ㅸ㉈⊘ᵋ䗅ㆁ㙊⫊ ₩⏍㐎ẝ嬵㕏ɿ 䙓ܡ䗑ࡴ • ᵎ壂Ề䑩嬦ᷨ␂⋃⒇㯢㙊㋩劑䗅₸ㅗ 弾⇡嫿⡈澤Ḧ忀₎⊲斪ɿ 㓈ᡸ • ㆁ㙊丵Ἧ⼆枼䑲嫥嬂䗅丵Ἧ᷻⎙弜垍ɿ 嫿⡈怩㯢 㙊䑩ㅸ⌰Ḧ㘵㊣䗅昷ḷɿᵻ忀₎℻䋱大䑶⊲斪ᵎ壂儫ⴲ 嬖☿㆔⹁嫿⡈䘗⪑丵Ἧ嬦嫿⡈ɿ 䗮亢ᄨ • 㙊ᷜ嫿⡈㙻⠴ᵋ㙊彛栏㤾ㅗ⪕澤⫄ḭ㕰䑩㚦敳㪣 㙻㒐だ₄ḷ弈䀮ɿ ᵎ壂䑩Ḽẖ
Table of Contents Chapter One • Installation and Operation ................... 1-1 About the IR 102 Kit ................................................................. 1-2 Mounting the IR 102 Rx remote receiver ........................... 1-2 Rack mounting ....................................................................... 1-2 UL requirements ............................................................... 1-3 Rack mounting instructions.............................................
Table of Contents, cont’d IR 102 Remote Control Kit 1 Chapter One Installation and Operation About the IR 102 Kit Mounting the IR 102 Rx remote receiver Connecting the IR 102 Rx to a Switcher Features and Connections Installing Batteries in the Remote Operation ii IR 102 Remote Control Kit • Table of Contents
Installation and Operation About the IR 102 Kit The Extron IR 102 Kit is an infrared (IR) remote control kit that can control a variety of Extron switchers and other devices via RS-232 or contact closure. This kit contains the following items: • (1) IR 102 handheld remote control • (1) IR 102 Rx remote receiver • (1) IR Sensor UL requirements The following Underwriters Laboratories (UL) requirements pertain to the installation of the IR 102 Rx into or onto a rack. 1.
Installation and Operation, cont’d Furniture mounting Furniture mount the IR 102 Rx remote receiver using optional mounting kit #70-212-01 as follows: 1. Use 2 mounting holes on opposite corners. (2) 4-40 x 3/16" Screws If rubber feet were previously installed on the bottom of the remote receiver, remove them. 3. Under Desk Mounting Hold the remote receiver with the attached brackets against the underside of the table or other furniture.
Installation and Operation, cont’d Projector Mounting Bracket Mounting Bolt Countoured Bracket Base Extron IR 102 RX Remote Receiver Side Mounting Plate U-bolt Extron IR 102 Rx Remote Receiver Power Supply Extron PMK 300 Multi-product Projector Mount Kit Projector Front Mounting Plate Projector mounting the IR 102 Rx using the PMK 100 mini projector mounting kit (#70-217-01) Mounting using the PMK 300 projector mounting kit Alternatively, the IR 102 Rx remote receiver can be projector mounted usi
Installation and Operation, cont’d N The PMK 300 has a hole in the bottom plate that allows the projector pole to be inserted through the center of the plate, rather than outside of the plate (see the illustration below). To install the PMK 300 in this configuration, slide the bracket up from the bottom of the pole before the projector is installed on the pole. Mounting using the PMK 350 projector mounting kit The IR 102 Rx can also be mounted using the PMK 350, as shown below.
Installation and Operation, cont’d 6. Place the PMK 350 mounting tray around the projector ceiling mounting pole. (See the illustration on page 1-9.) 7. Assemble the U-bolt and the following parts in the order they are listed below: Features and Connections 1 IR 102 Rx UNIVERSAL IR REMOTE RECEIVER POWER 12V .5A MAX c. Pass the U-bolt legs through the round holes in the contoured base. 2 d. Pass the U-bolt legs through the round holes in the L-shaped bracket. 8.
Installation and Operation, cont’d W N The two power cord wires must be kept separate while the power supply is plugged in. Remove power before continuing. e To verify the polarity before connection, plug in the power supply with no load and check the output with a voltmeter. c IR In connector — Plug the cable from the IR sensor or from an Extron IR Link infrared repeater into this 3.5 mm, 5-pole captive screw connector.
Installation and Operation, cont’d Installing Batteries in the Remote Control Operation The IR 102 handheld remote control is shown below. 1 INPUT/OUTPUT SELECTION 2 3 4 To select an input using the IR 102 remote control, aim the handheld unit at the IR detector and press the numeric button for the desired input. For switchers with ten or more inputs, press the +10 key to add ten to the input number selected. For example, to select input 17, press the +10 key, then the 7 key.
Installation and Operation, cont’d IR 102 Remote Control Kit A Appendix A Specifications, Part Numbers, and Accessories Specifications Included Parts Accessories 1-16 IR 102 Remote Control Kit • Installation and Operation
Specifications, Part Numbers, and Accessories Specifications These items are included in each order for an IR 102 Remote Kit (part #70-224-01): General Carrier frequency .......................... 38 kHz Max. IR range (between IR handheld remote control and IR sensor) 30 feet (9.1 meters) Max. IR sensor cable length ......... 21 feet (6.4 meters) External power supply (included) 100 VAC to 240 VAC, 50/60 Hz, external, autoswitchable; to 12 VDC, 1 A, regulated Power input requirements ...........
Specifications, Part Numbers, and Accessories Accessories A-4 Part number VersaTools multi-product projector mounting kit (PMK 300) 70-374-01 VersaTools multi-product projector mounting kit (PMK 350) 70-563-02, -03 IR 102 Remote Control Kit • Specifications, Part #s, Accessories
