Products

ManualsBrandsExtron Electronics ManualsHardwareHideaway Surface Access

HSA 402

AUDIO

PHONE

DATA

125 - 50/60 Hz 5A

PHONE

125 - 50/60 Hz 5A

HSA 402

DATA

Hideaway

Surface Access Products • Installation Guide

This guide provides instructions for an experienced installer to install and connect the

Extron HSA 400, HSA 402, and HSA 822.

The HSA units are lift-up architectural solutions for inconspicuous A/V connectivity access,

control, and AC power.

Planning

Determine the best location for the enclosure. Before making any cuts:

c Ensure that the location where the HSA is to be installed is convenient

for as many users as possible.

c Ensure that the edge on which the HSA opens is oriented correctly.

c Ensure that there is ample space under the table for cables.

c Ensure that the correct template or dimensions are used.

Decide on the method for cutting the hole in the table.

c Hand router and template

c CNC wood router

c Jigsaw and paper template

Before starting the installation, check with local and state regulations:

c Ensure that the planned installation complies with building

and electrical codes.

c Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility requirements.

Tools and Equipment Required for Installation

Safety Glasses

Screw Driver

Tape Measure

Vacuum Cleaner

7/16" Hex Nut Driver or Wrench (US)

10 mm Hex Nut Driver or Wrench (Int’l)

1/4" Hex Nut Driver (for AAPs)

Marking Pen

Square

Included Parts

HSA 400

HSA 402

Clamshell Bolts

(4) sets of (2)

(various lengths)

HSA 822

COMPUTER

AUDIO

125 - 50/60 Hz 5A

HSA 400

125 - 50/60 Hz 5A

HSA 402

Allen Wrench

(included with HSA 400

and HSA 402 only)

Zip Ties

Icon Kit

Bezel Kit

Tweeker (1)

AT 6

Summary of content (4 pages)

PAGE 1
Hideaway® Surface Access Products • Installation Guide This guide provides instructions for an experienced installer to install and connect the Extron HSA 400, HSA 402, and HSA 822. The HSA units are lift-up architectural solutions for inconspicuous A/V connectivity access, control, and AC power. Planning Determine the best location for the enclosure. Before making any cuts: c Ensure that the location where the HSA is to be installed is convenient for as many users as possible.
PAGE 2
HSA 400 / 402 / 822 • Installation Guide Preparing the Table Internal RJ-45 Cable Routing WARNING: Wear safety glasses when cutting the hole in the table. Failure to comply may result in eye injury. HSA 402 120-240 50/60 Hz 5A 120-240 50/60 Hz 5A Present on HSA 402 Only CAUTIONS: • The opening in the table for the HSA should be cut only by licensed and bonded craftspeople. • Exercise care to prevent scarring or damaging the furniture.
PAGE 3
Internal RJ-45 Cable Routing HSA 402 120-240 50/60 Hz 5A 120-240 50/60 Hz 5A Present on HSA 402 Only A B A B1 A1 A2 B2 C D B C D B1 A1 HSA 400 / HSA 402 B2 A2 Present on HSA 402 Only HSA 822 Cabling and Installing the AAPs 125 WARNING: Ensure that AC power is disconnected before removing the front - 50 /60 Hz 5A HSA 400 panel. 1. Remove and retain the four screws on the right and left sides of the front panel. Lift the panel away from the enclosure.
PAGE 4
HSA 400 / 402 / 822 • Installation Guide Installation Checklist Planning (page 1) Choose a location. Consider the following: Ensure that the edge on which the lid opens faces the table position of the most likely user. Ensure that there is ample space under the table for cable routing. Ensure that there is a nearby electrical outlet. Preparing the Table (page 2) Ensure that you are using the correct template or dimensions. Cut the hole.