User Guide Owner manual

Command/response table for Receiver SIS commands (continued)
Command ASCII Command
(host to unit)
Response
(unit to host)
Additional description
Video shutdown delay
NOTES: • The Set Video Delay command delays the digital video to help monitors sync correctly during an input rate change.
• Only video is delayed; embedded audio is not delayed.
Set delay
3*
X2!
# Dly
X2!]
Delay video by an interval of
X2!
.
Example:
3*3#
Dly3
]
Delay video by an interval of 0.75 seconds
(3 x 0.25 seconds).
View delay
3#
X2!]
Switch and signal status requests
Request Audio switch status
E
Stat
} X1%]
Show the position of the Audio switch:
0 = off (embedded audio is muted) or 1 = on (unmute).
NOTE: The audio on the captive screw audio output always remains active regardless of the setting of this switch.
Check audio embed
E
5Stat
}
EmbedAud
X1!]
Show if audio is embedded in the video stream:
0 = not detected or 1 = detected.
View link 1 (Tx-to-Rx) status
1S
X1!]
View link 2 (Rx-to-Tx) status
2S
X1!]
View input video status
3S
X1!]
View input audio status
4S
X1!]
View all signal status
5S
SigI
X1!
•SigO
X1!
•HdcpI
X1!
•HdcpO
X1!]
Report the status of the HDMI input, HDMI output
(always -- for a transmitter), HDCP encoding on the
input, and HDCP encoding on the output.
View HDMI signal status
6S
SigI
X1!
•SigO
X1!]
Report the status of the HDMI input and HDMI
output (always -- for a transmitter).
View HDCP status
7S
HdcpI
X1!
•HdcpO
X1!]
Report the status of the HDCP encoding on the
input and HDCP encoding on the output.
View temperature
20S
X1@
F•
X1@
C
]
Show temperature in degrees Fahrenheit and Celsius.
Information requests
Information request
I
1Lnk
X1!
•2Lnk
X1!
•Vid
X1!
•Aud
X1!
•
X1#
•Rx
]
The unit responds with the current status (signal
detected) of optical link 1, optical link 2, the
video input, and the audio link; the fiber optic
transmission mode (singlemode or multimode); and
the device type (Rx).
Show firmware version
Q
X1$]
Example:
Q
1.23
]
The factory-installed firmware version is 1.23
(sample value only).
Request part number
N
60-1174-nn
]
See “Part Numbers” in the “Reference
Information” section.
Resets
Reset memory presets
E
ZG
}
Zpg
]
Reset (erase) all memory presets.
System reset
E
ZXXX
}
Zpx
]
Reset all settings to factory defaults.
NOTE: X( = Mute and auto memory status 0 = off 1 = on
X1% = Switch position 0 = off (right) 1 = on (left)
X1! = Link status 0 = light or signal input not detected
1 = light or signal detected
X2! = Video delay 0 = 0 second
(0 plus six steps at 0.25 seconds per step) 1 = 0.25 second 3 = 0.75 second 5 = 1.25 second
2 = 0.5 second (default) 4 = 1.0 second 6 = 1.5 second
X1$ = Firmware version v.vv
X1@ = Internal temperature nnnF•nnC
FOXBOX Tx/Rx HDMI • Remote Control 25