User Guide Owner manual

Command/response table for Transmitter SIS commands (continued)
Command ASCII Command
(host to unit)
Response
(unit to host)
Additional description
Audio input gain and attenuation
NOTES: • The set gain (G) and set attenuation (g) commands are case sensitive. The increment level, decrement level, and show level are
not case sensitive.
• When the controlling PC is connected to the receiver, the PowerCage FOX can perform this command only if the receiver-Tx-to-
transmitter-Rx fiber cable is connected. The unit returns the E14 error if the Rx fiber is not connected.
Set input audio gain to a
+dB value
X^
G Aud
X&]
Set the input level to
X&
dB (gain).
Example:
2G
Aud+02.0
]
Set the input level to +2 dB (gain).
Set input audio attenuation
to a -dB value
X*
g Aud
X&]
Set the input level to
X&
dB (attenuation).
Increment input level
+G
Aud
X&]
Increase the audio level by 1 dB.
Example:
+G
Aud+03.0
]
Increment the input level from +2 dB to +3 dB.
Decrement input level
–G
Aud–01.0
]
Decrease the audio level from 0 dB to –1 dB.
Show input level
G
X&]
Plus mode transmission
NOTE: Plus mode forces the transmitter to emulate a FOXBOX DVI Plus or PowerCage FOX DVI Plus transmitter) .
Enable Plus mode
81*1#
Plus1
]
Turn on Plus mode (default).
Disable Plus mode
81*0#
Plus0
]
Turn off Plus mode.
View Plus mode
81#
X(]
Show Plus mode status.
Input reports as an HDCP authorized device
HDCP authorized device on
E
E1HDCP
}
HdcpE1
]
Set the transmitter as an HDCP authorized device.
HDCP authorized device off
E
E0HDCP
}
HdcpE0
]
Set the transmitter as not an HDCP authorized device.
View HDCP authorized
device status
E
EHDCP
} X1)]
Show HDCP authorized device status.
Status requests
View link 1 (Tx-to-Rx) status
1S
X1!]
View link 2 (Rx-to-Tx) status
2S
X1!]
View input video status
3S
X1!]
View input audio status
4S
X1!]
View all signal status
5S
SigI
X1!
•SigO
X1!
•HdcpI
X1!
•HdcpO
X1!]
Report the status of the HDMI input, HDMI output,
HDCP encoding on the input, and HDCP encoding
on the output.
View HDMI signal status
6S
SigI
X1!
•SigO
X1!]
Report the status of the HDMI input and HDMI
output (always -- for a transmitter).
View HDCP status
7S
HdcpI
X1!
•HdcpO
X1!]
Report the status of the HDCP encoding on the
input and HDCP encoding on the output.
View temperature
20S
X1@
F•
X1@
C
]
Show temperature in degrees Fahrenheit and Celsius.
NOTE: X^ = Audio gain adjustment range 00 to 10
X& = Audio level adjustment range -18 to +10 (in 1.0 dB steps)
X* = Audio attenuation adjustment range 00 to 18
X( = Enable or disable status 0 = off (down) or disable 1 = on (up) or enable
X1) = HDCP authorized device 0 = off 1 = on
X1! = Link and input status 0 = link or input not detected 1 = link or input detected
X1@ = Internal temperature nnnF•nnC
FOXBOX Tx/Rx HDMI • Remote Control 21