User Guide

Command and response table for SIS commands (continued)
Command ASCII Command
(host to unit)
Response
(unit to host)
Additional description
On-screen display timeout
Set menu timeout
EX1&
MDUR
}
Mdur
X1&]
Set the duration of the on-screen display.
View menu timeout
E
MDUR
}
Mdur
X1&]
View the duration of the on-screen display.
Switch and signal status requests
Request Audio switch status
E
STAT
}
EmbedAud
X1*]
Show the position of the Audio switch:
0 = off (embedded audio is muted) or 1 = on (unmute).
NOTE: The audio on the captive screw audio output always remains active regardless of the setting of this switch.
Check audio embed
E
5STAT
} X1(]
Show if audio is embedded in the video stream:
0 = not detected or 1 = detected.
View link 1 (Tx-to-Rx) status
1S
X1(]
View link 2 (Rx-to-Tx) status
2S
X1(]
View input video status
3S
X1@]
View input audio status
4S
X1@]
View all signal status
5S
SigI
X1(
•SigO
X1(
•HdcpI
X1(
•HdcpO
X1(]
Report the status of the HDMI input, HDMI output,
HDCP encoding on the input, and HDCP encoding on
the output.
View HDMI signal status
6S
SigI
X1(
•SigO
X1(]
Report the status of the HDMI input and HDMI output.
View HDCP status
7S
HdcpI
X1(
•HdcpO
X1(]
Report the status of the HDCP encoding on the input
and HDCP encoding on the output.
View temperature
20S
X2)
F•
X2)
C
]
Show temperature in degrees Fahrenheit and Celsius.
View SFP module status
40S
X2!
•
X2@
•
X2#
•
X2$]
Example:
40S
JDSC
•4.156mw•0.30mw•32C
Information requests
Information request
I
1Lnk
X1(
•2Lnk
X1(
•Vid
X1@
•Aud
X1@
•
X2%
•SR
]
The unit responds with the current status (signal
detected) of optical link 1, optical link 2, the video
input, and the audio link; and the fiber optic
transmission mode (singlemode or multimode).
Show firmware version
Q
X2^]
Example:
Q
1.23
]
The factory-installed firmware version is 1.23 (sample
value only).
Request part number
N
60-1187-nn
]
See “Part Numbers” on page 36.
Resets
Reset image settings
E
ZI
}
Zpi
]
Reset (clear) all image adjustments.
System reset
E
ZXXX
}
Zpx
]
Reset all settings to factory defaults.
NOTE: X1@ = On and off status 0 = off 1 = on
X1& = On-screen display timeout 0 = No display timeout 01 to 64 (seconds)
X1* = Switch position 0 = off (down) 1 = on (up)
X1( = Link status 0 = light or signal input not detected 1 = light or signal detected
X2) = Internal temperature nnnF•nnC
X2! = Vendor/manufacturer name
X2@ = Transmit output power in milliwatts
X2# = Receive optical power in milliwatts
X2$ = SFP temperature nnC
X2% = Transmission mode SM = singlemode MM = multimode
X2^ = Firmware version v.vv
FOXBOX SR HDMI • Remote Control 26