User`s manual

FOXBOX 4G Tx/Rx • Remote Control
Remote Control, cont’d 3-8
FOXBOX 4G Tx/Rx • Remote Control
3-9
Command ASCII Command
(host to unit)
Response
(unit to host)
Additional description
Pixel phase
N
When the controlling PC is connected to the receiver, the FOXBOX 4G can perform this command only if the receiver Tx to transmitter Rx
fiber cable is connected. The unit returns the E14 error if the Rx fiber cable is not connected.
Set a pixel phase value
X(
U Phs
X*]
Set the pixel phase value to
X(
.
Example:
10U
Phs10
]
Set the pixel phase value to 10.
Increment pixel phase +U
Phs
X*]
Increase pixel phase value by 1.
Decrement pixel phase -U
Phs
X*]
Decrease pixel phase value by 1.
Show pixel phase U
X(]
Total pixels
N
When the controlling PC is connected to the receiver, the FOXBOX 4G can perform this command only if the transmitter Tx to receiver Rx
fiber cable is connected. The unit returns the E14 error if the Rx fiber is not connected.
Set a total pixel value
11*
X1)
# Tpx
X(]
Set the total pixels to a specic value.
Example:
11*1555#
Tpx1555
]
Set the total pixel value to 1555.
Increment total pixel value +11#
Tpx
X(]
Increase total pixel value by 1 pixel.
Decrement total pixel value -11#
Tpx
X(]
Decrease total pixel value by 1 pixel.
Show total pixel value 11#
Tpx
X(]
List sync frequency
View input frequency 1LS
X1!
,
X1!]
List the input frequency as
X1!
kHz (horizontal) and
X1!
Hz (vertical.
Command/response table for SIS commands (continued)
Command ASCII Command
(host to unit)
Response
(unit to host)
Additional description
Memory presets
Save preset
X1@
,
Spr
X1!]
Command code is a comma.
Recall preset
X1@
.
Rpr
X1!]
Command code is a period.
Audio input gain and attenuation
N
The set gain (G) and attenuation (g) commands are case sensitive.
N
When the controlling PC is connected to the receiver, the FOXBOX 4G can perform this command only if the receiver Tx to transmitter Rx
fiber cable is connected. The unit returns the E14 error if the Rx fiber is not connected.
Set input audio gain to +dB
value
X1#
G Aud
X1$]
Example:
2G
Aud+02.0
]
Set the input audio gain to +2 dB.
Set input audio attenuation
to -dB value
X1%
g Aud
X1$]
Increment level +G
Aud
X1$]
Increase audio level by 1.0 dB.
Example:
+G
Aud+03
]
Increment the audio input level from +2 dB to +3 dB.
Decrement level -G
Aud
X1$]
Decrease the audio level by 1.0 dB.
Example:
-G
Aud-09
]
Decrement audio input level from -08 dB to -9 dB.
Show input gain G
X1$]
Command/response table for SIS commands (continued)
N
X(
= Pixel phase 0 to 31
X1)
= Total pixels ± 255 of the default value
X1!
= Sync frequency xxx.xx (frequency in kHz [H] or Hz [V])
N
X1@
= Memory preset number 1 to 30
X1#
= Audio gain adjustment range 0 to 10
X1$
= Audio level adjustment range -18 to +10 (in 1.0 dB steps)
X1%
= Audio attenuation adjustment range 0 to 18