User`s manual

FOXBOX 4G Tx/Rx • Remote Control
Remote Control, cont’d 3-6
FOXBOX 4G Tx/Rx • Remote Control
3-7
Command ASCII Command
(host to unit)
Response
(unit to host)
Additional description
Video mute
Mute output 1B
Blk1
]
Blank the video output.
Unmute output 0B
Blk0
]
Output video.
Show video mute status B
X!]
Video output mute status is
X!
(0 = unmuted, 1 = muted).
Display Data Channel (DDC) resolution and rate (FOXBOX 4G DVI only)
Set DDC resolution
41*
X@
*
X#
# DDC
X@
*
X#]
Select a DDC resolution.
Show DDC resolution 41#
X@
*
X#]
Show the DDC resolution.
Mode switch position
N
Only DIP switch 1 (the first
X$
) has any effect on the system operation. When the switch is on (up), the receiver is in daisy chain mode.
Show DIP switch position 8#
X$X$]
Show the rear panel DIP switch position.
Output sync format
Set output sync format
6*
X%
# Syn
Y%]
Set the sync format. 0 = RGBHV, 1 = RGsB.
Show output sync format 6#
X%]
Output sync polarity
Set output polarity negative 7*1#
Pol1
]
Set the receiver output polarity to always be negative.
Set polarity to the input 7*0#
Pol0
]
Polarity follows the video sync input to the transmitter.
Show output sync format 7#
X^]
Command/response table for SIS commands
Command ASCII Command
(host to unit)
Response
(unit to host)
Additional description
Horizontal shift
Set a horizontal position
X&
H Hph
X&]
Set horizontal centering to
X&
.
Increment position. +H
Hph
X&]
Shift the image one pixel to the right.
Decrement position -H
Hph
X&]
Shift the image one pixel to the left.
Show position H
X&]
Vertical shift
Set a vertical position
X&
/ Vph
X&]
Set vertical centering to
X&
.
Increment position +/
Vph
X&]
Shift the image down one line.
Decrement position -/
Vph
X&]
Shift the image up one line.
Show position /
X&]
Horizontal start
N
When the controlling PC is connected to the receiver, the FOXBOX 4G can perform this command only if the receiver Tx to transmitter Rx
fiber cable is connected. The unit returns the E14 error if the RX fiber is not connected.
Set a start position
X*
) Hst
X&]
Set the horizontal location of the rst active pixel in the
active window.
Example:
128)
Hst128
]
Set pixel 128 as the rst active pixel.
Increment start position +)
Hst
X&]
Increase the horizontal start location value.
Decrement start position -)
Hst
X&]
Decrease the horizontal start location value.
Show start position )
X*]
Command/response table for SIS commands (continued)
N
X!
= Mute status 0 or 1 (0=umuted and 1=muted)
X@
= Resolution 1 through 15. See page 3-3
X#
= Refresh rate 1 = 50 Hz 2 = 60 Hz
X$
= Mode switch position 0 = off (down) 1 = on (up)
X%
= Output sync format 0 = RGBHV 1 = RGsB
X^
= Output sync polarity 0 = follow input 1 = force sync to negative
N
X&
= Horizontal and vertical position 0 to 255
X*
= Horizontal start 0 to 255