User Guide

FOX RS 104 RS-232 Inserter • Remote Control 16
Command ASCII Command
(host to unit)
Response
(unit to host)
Additional description
Information requests (Continued)
Set IP address
EX1!
CI
}
Ipi
X1!]
Read IP address
E
CI
} X1!]
Read hardware address
E
CH
} X1@]
Reads MAC address.
Read # of open connections
E
CC
} X1#]
Set subnet mask
EX1!
CS
}
Ips
X1!]
Read subnet mask
E
CS
} X1!]
Set gateway IP address
EX1!
CG
}
Ipg
X1!]
Read gateway IP address
E
CG
} X1!]
Set administrator password
EX1$
CA
}
Ipa•
X1$]
Read administrator password
E
CA
} X1$]
Reset (clear) administrator
password
E
•CA
}
Ipa•
]
Set user password
EX1$
CU
}
Ipu•
X1$]
Read user password
E
CU
} X1$]
Reset (clear) user password
E
•CU
}
Ipu•
]
Set DHCP on or off
EX1%
DH
}
Idh
X1%]
Read DHCP on/off status
E
DH
} X1%]
Set serial port parameters
EX!
*
X1^
,
X1&
,
X1*
,
X1(
CP
}
Cpn
X!
•Ccp
X1^
,
X1&
,
X1*
,
X1(]
Read serial port parameters
EX!
CP
} X1^
,
X1&
,
X1*
,
X1(]
Set serial port mode
EX!
*
X2)
CY
}
Cpn
X!
•Cty
X2)] X2)
is always 0 (RS-232)
Read serial port mode
EX!
CY
} X2)]
Set verbose mode
EX2!
CV
}
Vrb
X2!]
Read verbose mode
E
CV
} X2!]
Configure current port timeout
E
0*
X2@
TC
}
Pti0*
X2@]
Read current port timeout
E
0TC
} X2@]
Configure global IP port timeout
E
1*
X2@
TC
}
Pti1*
X2@]
Read global IP port timeout
E
1TC
} X2@]
Set direct access port map
EX2#
MD
}
Pmd
X2#]
Reset direct access port map
E
2001MD
}
Pmd02001
]
Resets the direct access port number to 2001.
View direct access port map
E
MD
} X2#]
NOTE:
X!
= Port number 1 through 4
X1!
= IP address ###.###.###.###
X1@
= Hardware (MAC) address ##-##-##-##-##-##
X1#
= Number of open connections 0 – 200
X1$
= Password 12 alphanumeric characters
X1%
= DHCP 0 =off, 1 = on
X1^
= Baud rate 9600, 19200, 38400, 115200
X1&
= Parity odd, even, none, mark, space (Only the first letter required.)
X1*
= Data bits 7 or 8
X1(
= Stop bits 1 or 2
X2)
= Port type (always 0 = RS-232)
X2!
= Verbose mode 0 = clear/none (default for Telnet connection) 2 = tagged responses for queries
1 = verbose mode (default for RS-232) 3 = verbose mode and tagged for queries
X2@
= Port timeout interval 1 (= 10 seconds) – 65000 (default is 30 = 300 seconds = 5 minutes)
X2#
= Direct access port map 0 (= disabled) or 1024 and up (default is 2001)