User Guide User guide

Command/response table for Transmitter SIS commands (continued)
FOX II DP Transmitter and Receiver • Remote Control
22
Command SIS Command
(host to unit)
Response
(unit to host)
Additional description
Video shutdown delay
NOTES:
• The Set Video Delay command blanks the digital video for a specified time to help sink devices correctly detect an AV rate change.
• Only video is blanked; embedded audio is not muted.
Set delay
3*
X&
# Dly
X&]
Delay video by an interval of
X&
.
Example:
3*3#
Dly3
]
Delay video by an interval of 0.75 seconds
(3 x 0.25 seconds).
View delay
3#
X&]
Audio input format
NOTE: This command selects the audio input that is transmitted to the receiver.
Select auto
E
I0AFMT
}
AfmtI0
]
Transmit the digital audio embedded in the
DisplayPort input, if detected, otherwise transmit
the analog audio.
Select digital audio
E
I1AFMT
}
AfmtI1
]
Transmit the digital audio embedded in the
DisplayPort input.
Select analog audio
E
I2AFMT
}
AfmtI2
]
Transmit the analog audio input.
Show audio selection
E
IAFMT
} X*]
Show the selected format.
Audio mute (DisplayPort Loop-through and Return Out)
Mute the audio
X(
*1Z Amt
X(
*1
]
Silence the DisplayPort Loop-through audio,
Return Out audio, or both of the transmitter.
Example:
1*1Z
Amt1*1
]
Silence the DisplayPort Loop-through audio.
Unmute the audio
X(
*0Z Amt
X(
*0
]
The transmitter outputs Return Out audio.
Show audio mute status
X(
*Z
X1)]
Mute status of
X(
audio is
X1)
.
NOTE: 0 is not a valid
X(
value for the show audio mute status command.
Input reports as an HDCP authorized device
HDCP authorized device on
E
E1HDCP
}
HdcpE1
]
Set the transmitter as an HDCP-authorized device.
HDCP authorized device off
E
E0HDCP
}
HdcpE0
]
Set the transmitter as not an HDCP-authorized
device.
View HDCP authorized
device status
E
EHDCP
} X1)]
Show HDCP authorized device status.
Color bars test pattern
NOTE: The transmitter generates the color bars test pattern and sends it to the receiver. You must have the transmitter-Tx-to-receiver-Rx
fiber cable connected for the receiver to output the selected test pattern. The test pattern turns off if power is removed.
Output color bars test pattern
EX1!
Test
}
Test
X1!]
Set the transmitter to output the color bars test
pattern to the receiver.
X1!
defines the resolution
and rate.
Turn test pattern off
E
0Test
}
Test0
]
Set the transmitter to output the input video to
the receiver (no test pattern is selected).
Show test pattern status
E
Test
} X1!]
Transmitter name
Assign a name to the device
EX1@
CN
}
Ipn•
X1@]
Name the transmitter
X1@
.
Reset device name to default
E
•CN
}
Ipn•
X1@]
Name the transmitter “FOX II T DP“.
View the device name
E
CN
} X1@]
KEY: X& = Video delay (0 plus six steps at 0.25 seconds per step
) 0 = 0 second
1 = 0.25 second 4 = 1.0 second
2 = 0.5 second (default) 5 = 1.25 second
3 = 0.75 second 6 = 1.5 second
X* = Audio input for transmission
0 = Auto
1 = Digital (embedded DisplayPort) audio
2 = Analog audio
X(
= Audio output (DisplayPort Loop-through and Return Out) 0 = DisplayPort and analog 2 = Analog only
1 = DisplayPort only
X1) = HDCP and mute on or off status 0 = Off 1 = On
X1! = Color bars test pattern
0 = Off (default) 2 = 720p at 60 Hz
1 = 720p at 50 Hz 3 = 1080p at 60 Hz
X1@ = Transmitter name Up to 24 alphanumeric characters and hyphen (–)