User`s manual

FOX 500 Tx/Rx • Reference Information
Reference Information, cont’d
FOX 500 Tx/Rx • Reference Information
A-4
A-5
Sync
Input type ....................................... Autodetect RGBHV, RGBS, RGsB, RsGsBs
Output type .................................... RGBHV, RGBS, RGsB, RsGsBs
(follows input or can be set by user)
Input level ...................................... 2.5 V to 5.0 Vp-p
Output level ................................... TTL: 5.0 V p-p, unterminated, in HV or S;
or 0.3 V p-p on Gs, terminated
Input impedance ........................... 510 ohms
Output impedance ........................ 75 ohms
Polarity............................................ Positive or negative (follows input or can
be set by user)
Audio
Number/signal type ..................... 2 inputs (mixed): 1 balanced stereo,
1 unbalanced stereo
Gain
Range .................................. Adjustable, -18 dB to +24 dB
Default ................................ Unbalanced output: -6 dB;
balanced output: 0 dB
Frequency response ...................... 20 Hz to 20 kHz, ±0.5 dB
THD + Noise .................................. 0.10% @ 1 kHz at nominal level
S/N .................................................. >80 dB at maximum output (unweighted)
CMRR .............................................. >65 dB @ 20 Hz to 20 kHz
Sample size ..................................... 18 bits per channel, 2 channels (L and R)
Sampling rate ................................. 48 kHz
Audio input — transmitter (FOX 500 Tx)
Number/signal type ..................... 2 inputs (mixed): 1 balanced stereo,
1 unbalanced stereo
Connectors ..................................... (1) 3.5 mm captive screw connector, 5 pole
(1) 3.5 mm mini stereo jack
Impedance ...................................... 18k ohms unbalanced, 20k ohms balanced,
DC coupled
Nominal level ................................ +4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level .............................. +17 dBV, (unbalanced) at 1% THD+N
N
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu
Audio output — receiver (FOX 500 Rx)
Number/signal type ..................... 2 buffered outputs: 1 balanced stereo, 1
unbalanced stereo
Connectors ..................................... (1) 3.5 mm captive screw connector, 5 pole
(1) 3.5 mm mini stereo jack
Impedance ...................................... 50 ohms unbalanced, 100 ohms balanced
Nominal level ................................ +4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level (Hi-Z) ................. >+19 dBu, unbalanced at 1% THD+N
Maximum level (600 ohm) ........... >+15 dBm, unbalanced at 1% THD+N
Control/remote
Serial control ports on each unit (transmitter and receiver)
Control ................................ 1 RS-232, 3.5 mm captive screw connector,
5 pole (3 pins are used) (rear panel)
1 RS-232, 2.5 mm mini stereo jack (front
panel)
Pass-through ...................... 1 RS-232, 3.5 mm captive screw connector,
5 pole (3 pins are used) (rear panel);
in parallel with 1 RS-232, 2.5 mm mini
stereo jack (front panel)
Baud rate and protocol
Control ................................ 9600 baud, 8 data bits, 1 stop bit, no parity
Pass-through ...................... 9600 to 38400 baud
Serial control pin configurations
Captive screw connectors: 1 = Tx, 2 = Rx,
3 = GND
Mini stereo jack: tip = Tx, ring = Rx,
sleeve = GND
Program control ............................. Extron’s control/configuration program
for Windows
®
Extron’s Simple Instruction Set (SIS
™
)
General
Power .............................................. 100 VAC to 240 VAC, 50/60 Hz, 11 watts,
internal, autoswitchable
Temperature/humidity ................ Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Rack mount .................................... Yes, with optional 1U rack shelf, part
#60-190-01 or 60-604-01
Furniture mountable with optional under
desk mounting kit, part #70-077-01
Enclosure type ............................... Metal