Setup Guide Instruction Manual

ManualsBrandsExtron Electronics ManualsAccessories for videoDVI DL 201 Tx_Rx

Setup Guide — DVI DL 201 Tx/Rx

These instructions provide a quick setup guide for experienced installers. Installation

and service must be performed by authorized personnel only.

The DVI DL 201 Tx/Rx works with unshielded twisted pair (UTP) cable or shielded twisted

pair (STP) cable. STP cables are required to ensure FCC Class A and CE compliance.

Always use a power

supply speciﬁed by

Extron for this unit.

Use of an unauthorized

power supply voids all

regulatory compliance

certiﬁcation and

may cause damage

to the supply and the

transmitter or receiver.

One power supply is provided

when the transmitter and

receiver are purchased

together. A power supply is

not provided when either unit

is purchased separately.

Step 1

Turn off all equipment or disconnect

it from power sources. Mount the

transmitter and receiver as desired.

Follow the instructions included with the

appropriate mounting kit.

Step 2

Use the three port captive screw

connections to transmit pass-through

RS-232 and IR signals from a control

device to a remote device. RS-232 signals

are bidirectional and use three wires

(see diagram A. at right). IR signals are

unidirectional and use two wires (see

diagram B. at right). In each case the

control device is wired to the transmitter in

exactly the same way as the remote device

is wired to the the receiver.

The Extron

DVI DL 201 Tx and DVI DL 201 Rx are dual

link DVI transmitter (Tx) or receiver (Rx) units. Using

three CAT 5/5e/6/7 twisted pair cables, DVI-D signals

can be extended up to 100 feet (30 m) at resolutions up to

2560x1600 @ 60 Hz. They can be purchased as a pair or as

individual units.

DVI DL 201 Rx

DVI-D OUTPUT

Tx Rx

CONTROL

PASS THRU

12V

0.4A MAX

POWER

DVI-D INPUT

RS-232

PASS-THRU

DO NOT

CONNECT

OUTPUTS

TO LAN

DDC ROUTE

REMOTE

SPARE

LOCAL

LOCAL OUTPUT OUTPUT

Extron

DVI DL 201 Tx

Dual Link DVI

Transmitter

PC w/ Dual Link DVI

Output

Local

Monitor

Control

System

Dual Link

DVI Cable

RS-232

Extron

DVI DL 201 Rx

Dual Link DVI

Receiver

2560 x 1600 Flat Panel

Display with Dual-Link

DVI Input

CAT 5/5e/6/7 Cables

up to 200 feet

Tx Rx

CONTROL

ASS THRU

S G

DVI DL 201

Transmitter

or Receiver

IR Control

or IR emitter

Tx Rx

CONTROL

PASS THRU

Tx Rx

DVI DL 201

Transmitter

or Receiver

RS-232 Control

or Display Device

Step 3

Determine how the source device will obtain the EDID information and perform

one of the following procedures:

Option 1 — To capture the EDID of a desired display and store it in the EDID

Minder for future use:

a. Connect the display to the local monitor output of the transmitter.

b. Power on the transmitter and the local monitor.

c. Conﬁgure the DDC switches as shown in the ﬁgure at right.

1 2 3

OFF

DEFAULT EDID

EDID MINDER

REMOTE DDC

Summary of content (2 pages)

PAGE 1
Setup Guide — DVI DL 201 Tx/Rx The Extron® DVI DL 201 Tx and DVI DL 201 Rx are dual link DVI transmitter (Tx) or receiver (Rx) units. Using three CAT 5/5e/6/7 twisted pair cables, DVI-D signals can be extended up to 100 feet (30 m) at resolutions up to 2560x1600 @ 60 Hz. They can be purchased as a pair or as individual units. W These instructions provide a quick setup guide for experienced installers. Installation and service must be performed by authorized personnel only.
PAGE 2
Setup Guide — DVI DL 201 Tx/Rx (cont’d) d. Press and release the EDID “Store” button (see the figure at right). The rear panel LED turns amber while the EDID information is read and stored from the local monitor. Afterwards, the LED turns green. e. Power off and disconnect the display from the transmitter. f. Connect the transmitter to the receiver. EDID STORE g. Connect a source device to the transmitter. h.