User Guide DVI and HDMI DVI 110 DVI Signal Regenerator 68-1974-01 Rev.
Safety Instructions • English Warning This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. Power sources • This equipment should be operated only from the power source indicated on the product. This equipment is intended to be used with a main power system with a grounded (neutral) conductor. The third (grounding) pin is a safety feature, do not attempt to bypass or disable it.
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
iv
Contents Introduction.......................................................1 About this Guide ................................................. 1 About the DVI 110 Signal Regenerator ................. 1 Signal Eye Pattern ............................................ 1 Before Regeneration ............................................ 1 After Regeneration .............................................. 1 Features ........................................................... 2 Application Diagrams ...............
DVI 110 • Contents vi
Introduction This section gives an overview of the Extron DVI 110 Signal Regenerator and provides application examples. The following topics are covered: zz About this Guide zz About the DVI 110 Signal Regenerator zz Application Diagrams About this Guide This guide describes the functionality of the DVI 110 and provides procedures for connecting and operating it. In the guide, the terms “regenerator” and "DVI 110" are used interchangeably to refer to the product.
Features zz Output resolutions — Supports resolutions up to 1080p at 60 Hz and computer video signals up to 1920x1200. zz Power/Signal indicator — The bicolored LED on the front panel lights amber to indicate that power is on and green to indicate source signal presence. zz Data rates — Supports data rates of up to 4.95 Gbps; 1.65 Gbps per color. zz Supports DDC and HDCP — DDC channels are buffered, allowing pass-through of EDID and HDCP information between the source and the display.
DVI F-F AAP Laptop with DVI Output Short DVI Patch Cable Extron DVID SL Pro/50 DVI Cable UT TP I-D DV OU Extron DVI 110 OTE TS PU DVI Regenerator IN - SW UT 2 TP OU 1 1 UT TP OU UTO /A REM 3 4 2 TS PU IN WER PO V AX 12 M 0.4A Short DVI Patch Cable + Extron SW 4 DVI A DVI Switcher W/ Audio Display w/ DVI Input & Audio Figure 3.
Installation This section describes the features of the DVI 110 front and rear panels and provides instructions for cabling. It covers the following topics: zz Front and Rear Panel Features and Connections zz Connecting the DVI 110 Front and Rear Panel Features and Connections 2 DVI-D OUTPUT 1 4 POWER 12V 0.4A MAX DVI-D INPUT DVI 110 3 Figure 4. DVI 110 Front and Rear Panels a Power and signal status LED — This dual-color LED lights amber when the DVI 110 is receiving power.
9 1 8 17 24 16 Female Connector Male Connector Pin Signal Pin Signal Pin Signal 1 TMDS data 2– 9 TMDS data 1– 17 TMDS data 0– 2 TMDS data 2+ 10 TMDS data 1+ 18 TMDS data 0+ 3 TMDS data 2 shield 11 TMDS data 1 shield 19 TMDS data 0 shield 4 Spare 12 Spare 20 Spare 5 Spare 13 Spare 21 Spare 6 DDC clock 14 +5 V power 22 TMDS clock shield 7 DDC data 15 Ground (+5 V) 23 TMDS clock+ 8 CEC control 16 Hot plug detect 24 TMDS clock– Figure 5.
CAUTIONS: • When you are connecting the power supply, voltage polarity is extremely important. Applying power with incorrect voltage polarity could damage the power supply and the regenerator. Identify the negative lead by the ridges on the side of the cord (see the illustration on page 5). To verify the polarity before connection, plug in the power supply with no load and check the output with a voltmeter. • Do not tin the stripped power supply leads before attaching the captive screw connector.
Reference Information This section reference information for the DVI 110 signal regenerator. Topics that are covered include: zz Specifications zz Part Numbers zz Mounting the DVI 110 Specifications NOTE: *Appropriate DVI-D to HDMI cables or adapters are required for HDMI signal input and output.
Vibration ���������������������������������������� Regulatory compliance Safety �������������������������������������� EMI/EMC ��������������������������������� MTBF ��������������������������������������������� Warranty ���������������������������������������� ISTA 1A in carton (International Safe Transit Association) CE, c-UL, UL CE, C-tick, FCC Class A, ICES, VCCI 30,000 hours 3 years parts and labor NOTES: All nominal levels are at ±10%. Specifications are subject to change without notice.
Part Numbers Included Parts These items are included with DVI 110: Included Parts Replacement Part Numbers DVI 110 DVI Signal Regenerator 60-1145-01 PS 1210 C,12 VDC, LPS, Class 2, 1 A external power supply with captive screw connector 70-775-01 IEC power cord DVI 110 Setup Card Rubber feet, self-adhesive (4, not attached) Optional Accessories These items are optional and may be ordered separately: Accessories Part Numbers DVI 101 Cable Equalizer 60-873-01 RSU 129 9.
Mounting the DVI 110 The DVI 110 can be mounted on a rack shelf or under furniture, or it can be placed on a table top. Extron has a variety of optional rack shelf and furniture mounting kits that can be used with the DVI 110. See "Optional Accessories" in the "Reference Information" section for information on the mounting products available for the DVI 110. Tabletop Use Four self-adhesive rubber feet are included with the DVI 110.
Rack mounting procedure For optional rack mounting, mount the DVI 110 on one of the available rack shelves. On the standard 9.5 or 6 inches deep rack shelf, the DVI 110 mounts in one of eight possible locations to the rear of the rack. Use 2 mounting holes on opposite corners. 1/4 Rack Width Front False Faceplate Both front false faceplates use 2 screws. 1/2 Rack Width Front False Faceplate 1U Universal Rack Shelf (2) 4-40 x 3/16" Screws Figure 7. Mounting the DVI 110 on a Standard 9.
7. Insert #8 wood screws into the four pilot holes. Tighten each screw into the mounting surface until slightly less than 1/4 inch of the screw head protrudes. 8. Align the mounting screws with the slots in the brackets and place the unit against the surface, with the screws through the bracket slots. 9. Slide the unit slightly forward or back, then tighten all four screws to secure it in place.
Extron® Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase.
