Setup Guide Matrix Switchers DMS 1600 DMS 3600 Configurable Digital Video Matrix Switchers N Extron USA - West Headquarters +800.633.9876 Inside USA and Canada Only Extron USA - East Extron Europe Extron Asia Extron Japan +800.633.9876 Inside USA and Canada Only +800.3987.6673 Inside Europe Only +800.7339.8766 Inside Asia Only +81.3.3511.7655 +400.883.1568 +81.3.3511.7656 FAX Inside China Only +31.33.453.4040 +65.6383.4400 +1.919.863.1794 +31.33.453.4050 FAX +65.6383.4664 FAX +1.714.491.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
安全须知 • 中文 警告 这个符号提示用户该设备用户手册中 有重要的操作和维护说明。 电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 必须使用有地线的供电系统供电。 第三条线 （地线）是安全设施，不能不用或跳过。 这个符号警告用户该设备机壳内有暴 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后 或桌面电源的电源线，或任何接到市电系统的电源线。 露的危险电压，有触电危险。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 注意 阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理 解所有安全和使用说明。 保存说明书 • 用户应保存安全说明书以备将来使 用。 遵守警告 • 用户应遵守产品和用户指南上的所有安 全和操作说明。 维护 • 所有维修必须由认证的维修人员进行。 设备内部 没有用户可以更换的零件。为避免出现触电危险不要自 己试图打开设备盖子维修该设备。 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止 机内敏感元件过热。 不要用任何东西挡住通风孔。 锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用 与厂家推荐的相同
Contents Introduction ........................................1 Remote Control ................................11 About this Guide .................................1 About the DMS 1600 and DMS 3600 ..........................................2 Configurability ....................................3 Selected SIS Commands ....................11 Establishing a Network (Ethernet) Connection ..................11 Establishing a USB Port Connection ....................................
Introduction This section gives an overview of the DMS 1600 and DMS 3600 and describes their features. Topics that are covered include: • About this Guide • About the DMS 1600 and DMS 3600 About this Guide NOTES: • For more information on any subject in this guide, see the DMS 1600 and DMS 3600 User Guide, available on the Extron DVD or at www.extron.com.
About the DMS 1600 and DMS 3600 Configurability A B D A B C D A B C D A B 17 - 20 A B 21 - 24 A B A B A B A B A B A B 1-4 D C 25 - 28 B 9 - 12 C 29- 32 B A DVI-D INPUTS 33 - 36 A 13- 16 The DMS 1600 and DMS 3600 (see figure 1) are configurable matrix switchers that distribute DVI signals. I/O boards route signals that are compatible with all Extron DVI video product lines. The matrix switcher routes any input signal to any combination of outputs.
Installation This section describes installation of the DMS matrix switchers, including connections and features. Topics that are covered include: • Rear Panel • Front Panel Rear Panel A Note on I/O Boards See figure 2. Each I/O board is identified by the input and output connector numbers supported by the board position. The input and output numbers on the boards are identified as locations A through D.
1 1-4 8 A B A B 5-8 ANAHEIM, CA Making Connections 2 DVI-D INPUTS DVI-D INPUTS C D A B C D A B DVI-D OUTPUTS DVI-D OUTPUTS C D C D a DVI-I Input connectors — Connect DVI cables between these ports and the DVI output ports of the digital video sources. b DVI-I Output connectors — Connect DVI displays for the routed direct digital image. DVI-D INPUTS 9 - 12 c Remote port — If desired, connect a control system or computer to the rear panel Remote RS-232/RS-422 port.
Front Panel Operations Front Panel CONTROL CONFIG ENTER PRESET VIEW ESC PRIMARY REDUNDANT POWER SUPPLY DMS 1600 TMDS DIGITAL MATRIX SWITCHER 9 10 Figure 6. Front Panel Features i Configuration port — If desired, connect a control system or computer to the front panel Configuration port, a mini USB B port. j Primary and Redundant Power Supply LEDs — NOTE: The meaning of these indicators is identical to the LEDs on the power supplies (item g).
Saving or Recalling a Preset 1. Save a preset — Press and hold the Preset button until it flashes. Save a preset PRESET 2 seconds PRESET Press and hold. The Preset button blinks. Recall a preset — Press and release the Preset button. Recall a preset PRESET PRESET Press and release. The Preset button lights. All input and output buttons with assigned presets light red. When a preset is saved, the configuration data at assigned preset locations will be overwritten.
Connection timeouts The Ethernet link times out and disconnects after a designated period of time of no communications. By default, this timeout value is set to 5 minutes but the value can be changed (see the "Configure port timeout SIS command" on page 17.) NOTE: Extron recommends leaving the default timeout at 5 minutes and periodically issuing the Query (Q) command to keep the connection active or disconnecting the socket and reopening the connection when necessary.
14 Command/Response Table for SIS Commands DMS 1600 and DMS 3600 • Remote Control Command ASCII Command Response (Host to Unit) (Unit to Host) Additional Description Create ties NOTES: • • • • Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*02&003*003%. The matrix switchers support 1-, 2-, and 3-digit numeric entries (1*1!, 02*02&, or 003*003%). The ! tie command, the & tie command, and the % tie command can be used interchangeably.
16 Command DMS 1600 and DMS 3600 • Remote Control ASCII Command Response (Host to Unit) (Unit to Host) Information requests Information request I Request part number N Request part number and board configuration Query controller firmware version Example: *N VX%XX^•AX%XX^•SX&1X&2...X&n] In the response: VX%XX^ shows the number of available inputs and outputs for this configuration. AX%XX^ has no meaning for this product. SX&1X&2...X&n shows the board type installed in each slot.
Installing and Starting the Control Program Another way to operate the switcher is via the Windows®-based Matrix Switchers Control Program. This program is contained on the Extron Software Products DVD (included with the switcher). Run this program on a PC connected to a serial port (item c on page 7), Ethernet port (item d on page 7), or USB port (item i on page 8) on the switcher. The program must be installed on a Windows-based computer and cannot be run from the DVD.
2. On the next page that appears, select the Install the software automatically radio button and click Next. Follow the on-screen instructions. The wizard assigns the driver necessary to access the switcher to the connected Configuration (USB) port (this may take a few minutes). 3. If you selected IP [LAN] in step 2, the IP Connection window appears. 3. Click Finish to exit the wizard.
Accessing the HTML Pages NOTE: Another way to configure and operate the switcher is via its factoryinstalled HTML pages, which are always available and cannot be erased or overwritten. The HTML pages that are pre-loaded on the switcher are accessible through its LAN port, connected via a LAN or WAN, using a web browser such as Microsoft® Internet Explorer® (see item d on page 7, for connection information.
4. Press the keyboard key. The switcher checks whether it is password-protected. If the switcher is not password-protected, it checks and downloads the HTML start-up page. The switcher is ready for operation via HTML remote control. Maintenance and Modifications If the switcher is password-protected, it downloads the Enter Network Password dialog box. This section describes repairing and reconfiguring the DMS matrix switchers by replacing components.
Removing and Installing a Power Supply Module Align the board edges with the plastic guides. D S 44 DV I DM UT S C TP I-D D OU DV S 44 I DM B UT S C S C TP I-D D OU DV S 44 A DV CAUTION: I DM B UT TP I-D OU LY DV D DV The two power supply modules (primary power supply and redundant power supply) are identical and hot-swappable. Each power supply module has a two-color LED, visible on the rear panel, that indicates the status of the power supply outputs.
5. Align the flanges on the power supply module with the left and right power supply guides. 3. Gently pull on the screws to loosen the fan from the backplane. 4. Slide the fan out of the chassis. 6. Gently slide the power supply module into the enclosure until the power supply meets resistance. 5. Orient the fan to be installed so that the printing on the back of the panel is right-side up. 7. Gently seat the power supply in the backplane. 6.
