User’s Manual CSVEQ 100 D Composite Video and S-Video Line Driver with Audio Extron USA - West Headquarters +800.633.9876 Inside USA / Canada Only +1.714.491.1500 +1.714.491.1517 FAX Extron USA - East Extron Europe Extron Asia Extron Japan Extron China Extron Dubai +800.633.9876 +800.3987.6673 +800.7339.8766 Inside Europe Only Inside Asia Only +81.3.3511.7655 +81.3.3511.7656 FAX +400.883.1568 Inside USA / Canada Only +971.4.2991800 +971.4.2991880 FAX +1.919.863.1794 +1.919.863.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
安全须知 • 中文 警告 这个符号提示用户该设备用户手册中 有重要的操作和维护说明。 电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 必须使用有地线的供电系统供电。 第三条线 （地线）是安全设施，不能不用或跳过。 这个符号警告用户该设备机壳内有暴 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后 或桌面电源的电源线，或任何接到市电系统的电源线。 露的危险电压，有触电危险。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 注意 阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理 解所有安全和使用说明。 保存说明书 • 用户应保存安全说明书以备将来使 用。 遵守警告 • 用户应遵守产品和用户指南上的所有安 全和操作说明。 维护 • 所有维修必须由认证的维修人员进行。 设备内部 没有用户可以更换的零件。为避免出现触电危险不要自 己试图打开设备盖子维修该设备。 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止 机内敏感元件过热。 不要用任何东西挡住通风孔。 锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用 与厂家推荐的相同
Quick Start Guide — CSVEQ 100 D C Installation and service must be performed by authorized personnel only. These line drivers must be used with UL approved, grounded electrical boxes. To install and set up the line driver, follow these steps and see the appropriate sections of this manual for details. Step 1 Turn the input and output devices off and unplug their power cords. Verify that the line driver is disconnected from the power source before proceeding.
Quick Start — CSVEQ 100 D, cont’d When using long cables, follow these steps: a. Supply the color bars test signal to the input. (Recommendation: use an Extron VTG 300 Video Test Generator to generate the test signal.) b. Adjust the Gain control(s) for the output until the signal level at the far end is the same as the input (or the display shows the correct brightness and contrast). c.
Table of Contents Chapter One • Introduction ................................................... 1-1 About this Manual ..................................................................... 1-2 Features ......................................................................................... 1-2 Chapter Two • Installation ...................................................... 2-1 Application Example ................................................................. 2-2 Installing the CSVEQ 100 D ..........
Table of Contents, cont’d TOC-ii CSVEQ 100 D • Table of Contents
CSVEQ 100 D 1 Chapter One Introduction About this Manual Features
Introduction About this Manual The CSVEQ 100 D is a high performance composite video, S-video, and audio line driver designed to compensate for signal attenuation and high frequency loss encountered during long cable runs. It is capable of simultaneously driving composite video and S-video plus audio signals up to 1000 feet (300 m) on Extron MHR or RG59 high resolution video cables and STP series audio cables.
CSVEQ 100 D 2 Chapter Two Installation Application Examples Installing the CSVEQ 100 D
Installation Application Example To get started, refer to the "Quick Start Guide" at the beginning of this manual. C Installation and service must be performed by authorized personnel only.
Installing the CSVEQ 100 D The CSVEQ 100 D is a wall-mounted product and can be mounted into an electrical wall box. This section includes site preparation, wall box installation, and the mounting of the line driver in the wall box. N The line driver must be installed into an Underwriters Laboratories (UL) approved electrical wall box. The box is not included with the line driver; the installer is responsible for obtaining and installing the box.
Installation, cont’d Wall Stud Installation Cable Wall Stud Installation Cable Cable Clamp Cable Clamp Screws or Nails Screws or Nails Attaching the wall box to a wall stud If attaching the wall box to wood, use four #8 or #10 screws or 10-penny nails. A minimum of ½" (1.3 cm) of screw threads must penetrate the wood. If attaching the wall box to metal studs, use four #8 or #10 self-tapping sheet metal screws or machine bolts with matching nuts.
4. Mount the line driver to the wall box with machine screws as shown in the following illustration. Extron CSVEQ 100 D Wall Box O DE S-VI IN O IN VIDE Wall opening is flush with edge of box. DIO AU IN R L Decora Faceplate Mounting the line driver to a wall box 5. Attach the Decora® wall plate to the line driver as shown in the illustration above. 6. Reconnect the power supply, connect input cables to the line driver, and restore power to the equipment.
Installation, cont’d 5. Insert the mud ring into the hole. 6. Tighten all of the dogleg screws until the doglegs clamp the mud ring to the mounting surface. Do not overtighten. Standard mud rings only: If you are going to screw the mud ring to the surface, rather than using the detachable doglegs, mark the four surface mounting screw holes at the corners of the mud ring.
Testing and troubleshooting 1. Apply power to the line driver. The power/signal LED on the line driver lights amber (power) or green (video input). 2. If the LED does not light, check the wiring at both the line driver and the power supply, and make sure the power supply is connected to a power source. If the image does not appear or there is no sound 1. Make sure that all the devices are powered on. 2. Ensure that the connectors are wired correctly at both ends of the cables.
Installation, cont’d 2-8 CSVEQ 100 D • Installation
CSVEQ 100 D 3 Chapter Three Operation Front Panel Features and Operation Rear Panel Features and Operation Replacing the Decora Faceplate
Operation Front Panel Features and Operation Wall Plate Faceplate 1 S-VIDEO IN VIDEO IN 3 2 AUDIO IN R L 4 Wall Plate Mounting Screw CSVEQ 100 D Front Panel a b c Power indicator LED — This LED lights: • Amber when the line driver is receiving full power • Green when the line driver is receiving a video signal Video input connector — Connect a composite video input source to this RCA connector. S-video input connector — Connect an S-video input source to this 4-pin mini DIN connector.
d Audio input connectors — Connect an unbalanced stereo audio source to these left (L) and right (R) RCA connectors. Wire the male connector as shown in the following illustration.
Operation, cont’d C GAIN Y GAIN 6 7 GAIN VIDEO VIDEO OUTPUT 4 AUDIO OUTPUT CONFIG JUMPER POSITION OFF = DUAL MONO ON = STEREO 5 8 EQ CSVEQ 100 D EQ Rear Panel Features and Operation 9 AUDIO OUTPUT 3 1 2 CSVEQ 100 D Rear Panel a b 3-4 Power connector — Connect the external 12 VDC power supply into this 2-pin, 3.5 mm direct insertion connector. The power supply is included with the unit. The "Power supply wiring" section in this chapter explains how to wire the connector.
Balanced Stereo Left Tip (+) Left Ring (-) Sleeve (s) Right Tip (+) Right Ring (-) Unbalanced Stereo Left Tip (+) AUDIO OUTPUT CONFIG JUMPER POSITION OFF = DUAL MONO ON = STEREO Sleeve Right Tip (+) AUDIO OUTPUT CONFIG JUMPER POSITION OFF = DUAL MONO ON = STEREO Set Audio Output jumper to Stereo. Set Audio Output jumper to Stereo. Balanced Mono Unbalanced Mono Use either the left or the right channel. Use either the left or the right channel.
Operation, cont’d f g h i Output equalization (EQ) potentiometer (luma) — Use a small screwdriver to rotate this control to adjust equalization when the line driver is connected to long output cables. The adjustment range is 0 dB to +7 dB. The default is set to 0 dB (the dot position). See "Equalization (EQ) adjustment control" in this chapter.
W The two power cord wires must be kept separate while the power supply is plugged in. Remove the power before wiring. N Do not tin the power supply leads before installing in the direct insertion connector. Tinned wires are not as secure in the connectors and could be pulled out. Gain adjustment control The gain control adjusts picture brightness by compensating for signal amplitude loss caused by cable resistance.
Operation, cont’d Use a small, flat-blade screwdriver to rotate this control. View the display and select the setting that gives the sharpest picture. For a more precise setting, you can use an oscilloscope or a waveform monitor connected to the far end of the output cable, and adjust the equalization so that the color burst ranges between -20 IRE and +20 IRE. N The EQ control is a potentiometer with a mechanical stop at the high and the low end.
CSVEQ 100 D A Appendix A Specifications, Part Numbers, and Accessories Specifications Included Parts Optional Accessories
Specifications, Part Numbers, and Accessories Specifications Video Gain ������������������������������������������������� Composite video and Y of S-video: -1 dB to +3 dB (x0.9 to x1.
Sync Standards ���������������������������������������� NTSC 3.58, NTSC 4.43, PAL, SECAM Audio Gain ������������������������������������������������� Unbalanced output: 0 dB; balanced output: +6 dB Frequency response ���������������������� 20 Hz to 20 kHz, ±0.5 dB THD + Noise ���������������������������������� 0.
Specifications, Part Numbers, Accessories, cont’d Temperature/humidity ���������������� Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing Cooling ������������������������������������������� Convection, no vents Mounting ���������������������������������������� Wall or furniture mountable with standard US electrical wall boxes or mud rings Enclosure ���������������������������������������� Metal rear enclosure, plastic face
Included Parts These items are included in each order of the CSVEQ 100 D.
Specifications, Part Numbers, Accessories, cont’d Accessory MHR-2 SV mini high resolution S-video cables AV RCA cable STP cable A-6 CSVEQ 100 D • Specifications and Parts Part number 26-316-xx IN8906, IN8920 Various
CSVEQ 100 D B Appendix B Dimensions and Template CVEQ 100 D Dimensions Cut-out Template
Dimensions and Template CSVEQ 100 D Dimensions 1.72” (4.30 cm) 0.00” (0.00 cm) Dimensions are shown in inches [mm}. 0.06” (0.15 cm) 0.46” (1.55 cm) 0.10” (0.25 cm) 2.83” (7.19 cm) 0.00” (0.00 cm) 2.72” (6.91 cm) 1.92” (4.86 cm) 0.92” (2.32 cm) 0.11” (0.28 cm) 2.74” (6.96 cm) Front View B-2 CSVEQ 100 D • Dimensions and Template Side View 0.56” (1.43 cm) 0.00” (0.00 cm) 0.10” (0.25 cm) 0.06” (0.15 cm) 0.23” (0.57 cm) 1.60” (4.06 cm) 1.55” (3.94 cm) 1.45” (3.67 cm) 0.16” (0.39 cm) 0.
Cut-out Template N Always check and go by the dimensions given in this appendix. The template is not full size. Cut-Out Template for the Extron CSVEQ 100 D 2.79" (7.09 cm) Wall Plate 1.75" (4.5 cm) Location of Line Driver 4.50" (11.43 cm) 2.8" (7.1 cm) SURFACE CUT-OUT AREA FOR FURNITURE MOUNT To install line driver directly into furniture or wall, cut along this line.
Dimensions and Template, cont’d B-4 CSVEQ 100 D • Specifications and Parts
CSVEQ 100 D • Specifications and Parts B-5
Dimensions and Template, cont’d B-6 CSVEQ 100 D • Specifications and Parts
