Setup guide
Table Of Contents
- DTP CrossPoint 84 IPCP
- Safety Instructions
- FCC Class A Notice
- Contents
- Introduction
- Installation
- Front Panel Operations
- Remote Control
- Selected SIS Commands
- Establishing a Network (Ethernet) Connection
- Number of Connections
- Establishing a USB Port Connection
- Host-to-Switcher Instructions
- Common SIS Command Symbols
- SIS Command and Response Table for Matrix Switcher Commands
- Installing and Starting the Control Programs
- Starting the Product Configuration Software
- Starting the DSP Configurator Program
- Accessing the HTML Pages
- Selected SIS Commands
- Extron Warranty
- Contact Info
8 DTP CrossPoint 84 IPCP • Installation 9DTP CrossPoint 84 IPCP • Installation
Serial and IR Insertion Connections
SIG LINK
OUT
SIG LINK
IN
SIG LINK
IN
SIG LINK
OUT
1
3
4
4
XTP
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx Rx
XTP
S/PDIF
OUT
DTP
XTP
DTP
XTP
DTP
HDBT
G
DTP
HDBT
2
1234
5
8
6
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
INPUTS
OUTPUTS
RS-232 IR
Tx Rx Tx RxG
Figure 6. Serial and IR Insertion Connections
O
Over TP (Inputs 7 and 8) Ports — Plug serial RS-232
RS-232 IR
Tx Rx Tx RxG
signals, modulated IR signals, or both into these 3.5 mm,
5-pole captive screw connectors to insert bidirectional
RS-232 and IR communications. See RS-232 and IR
connectors on page 13 to wire the connectors.
P
Over TP (Outputs 3 and 4) Ports — Plug serial RS-232
RS-232 IR
Tx Rx Tx RxG
signals, modulated IR signals, or both into these 3.5 mm,
5-pole captive screw connectors to insert bidirectional
RS-232 and IR communications. See RS-232 and IR
connectors on page 13 to wire the connectors.
Control Connections
Tx Rx
RTSCTS
GTxRxG Tx Rx G
Tx Rx G
LAN 2
LAN 1
LAN 3
R
REMOTE
CONTROL
1234G
DIGITAL I/OCOM 3COM 2COM 1
SSGG
1
1
2
2
C34C
-S G+S+V
PWR OUT = 6W
IR/SERIALeBUSRELAYS
Figure 7. IPCP Control Processor and Remote Port
Q
IPCP control processor —The DTP CrossPoint 84 includes a built-
in IPCP control processor that can control and monitor a variety of
external devices. The IPCP offers RS-232 and IR-based control,
relays, and digital I/O controls. See the IPCP Pro Series Setup Guide,
included in the carton with the switcher to make all connections and
to congure and operate the IPCP control processor.
R
Remote Port — Plug a serial RS-232 device into the matrix
Tx Rx G
REMOTE
switcher via this 3.5 mm, 3-pole captive screw connector for
remote control of the switcher (see RS-232 and IR
connectors on page 13 to wire the connector).
Switcher Reset
S
Switcher Reset button and LED — Initiates four levels of
RESET
matrix switcher reset. For different reset levels, press and hold
the recessed button while the switcher is running or while you
power up the switcher.
See the DTP CrossPoint 84 IPCP Series User Guide, available at
www.extron.com.
Power
T
Power connector — Plug the switcher into a grounded AC source.
Additional Connector Information
HDMI connectors
Use a LockIt Lacing Bracket to securely fasten each HDMI cable to the
switcher as follows.
1. Plug the HDMI cable into
3
33
11
55
44
22
the panel connection.
2. Loosen the HDMI
connection mounting screw
from the panel enough
to allow the LockIt lacing
bracket to be placed over it.
The screw does not have to
be removed.
3. Place the LockIt lacing
bracket on the screw
and against the HDMI
connector, then tighten
the screw to secure the
bracket.
ATTENTION:
• Do not overtighten the HDMI connector mounting screw. The
shield it fastens to is very thin and can easily be stripped.
• Ne serrez pas trop la vis de montage du connecteur HDMI.
Le blindage auquel elle est attachée est très n et peut
facilement être dénudé
4. Loosely place the included tie wrap around the HDMI connector and
the LockIt lacing bracket as shown.
5. While holding the connector securely against the lacing bracket, use
pliers or similar tool to tighten the tie wrap, then remove any excess
length.