Setup guide

6 DTP CrossPoint 84 IPCP • Installation 7DTP CrossPoint 84 IPCP • Installation
SIG LINK
OUT
1
3
4
4
XTP
RS-232 IR
Tx Rx Tx Rx
XTP
S/PDIF
OUT
DTP
HDBT
G
DTP
HDBT
2
RS-232 IR
Tx Rx Tx RxG
OVER TP
OUTPUTS
SIG LINK
OUT
Figure 3. Video Output Features
D
HDMI Output 1 and 2 — Plug HDMI video displays (or DVI
with appropriate adapters) into these ports. See HDMI
connectors on page 9 to secure the connector to the board
with a LockIt HDMI Cable Lacing Bracket.
E
TP (XTP/HDBT/DTP switches, outputs 3 and 4 —
XTP
DTP
HDBT
ATTENTION:
• Position this switch BEFORE connecting the
appropriate device to the TP connector. Failure to
comply can damage the endpoint.
• Positionnez le sélecteur AVANT de connecter
l’appareil approprié au connecteur TP. Ne pas
respecter cette procédure pourrait endommager le
point de connexion.
XTP position — Select if the receiving device is an Extron XTP matrix
switcher. The output is HDMI with embedded audio plus RS-232 and IR.
HDBT position — Select if the receiving device is a HDBaseT-enabled
device. The output is HDMI with embedded audio plus RS-232 and IR.
DTP position — Select if the receiving device is an Extron DTP
device. The TP output is compatible with a DTP receiving device and
consists of HDMI with embedded audio, analog audio, RS-232 and
IR, and remote power.
F
TP Outputs 3 and 4 — Plug compatible Extron DTP
SIG LINK
OUT
receivers, XTP matrix switchers, or HDBaseT-enabled
devices into these RJ-45 ports using STP cables. See TP
connectors on page 10 to wire the connector.
ATTENTION:
• Do not connect this port to a computer data or
telecommunications network.
• Ne connectez pas ces port à des données informatiques ou
à un réseau de télécommunications.
Audio Inputs and Outputs
4
Tx Rx G
S/PDIF
OUT
EXP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
REMOTE
AUDIO INPUTS
AUDIO OUTPUTS
DMP EXPANSION
1
LR
1
LR
3
LR
3
LR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
RESET
1
L
R
4
CLASS 2 WIRING
8/
AMP OUTPUT
Figure 4. Video Output Features
G
Audio Inputs 1 through 6 — Plug balanced or unbalanced
LR
stereo audio inputs into these 3.5 mm, 5-pole captive screw
connectors (see Local and Mic/line audio connectors on
page 13 to wire the connectors).
H
Mic/Line Inputs 1 through 4 — Plug microphones or other
mono audio inputs into these 3-pole, 3.5 mm captive screw
connectors (see Local and Mic/line audio connectors on
page 13 to wire the connectors).
I
+48 V (phantom power) LEDs — Light to indicate +48 V
+48V
1
2
phantom power is switched on via software.
J
Audio Outputs 1 through 4 — Plug audio devices such
LR
as an audio amplifier or powered speakers to these 3.5 mm,
5-pole captive screw connectors (see Local and Mic/line
audio connectors on page 13 to wire the connectors).
K
Amp Output 1 (stereo audio model) — Plug passive,
1
L
R
4
CLASS 2 WIRING
8/
4-ohm or 8-ohm speakers to this 5 mm 4-pole captive
screw connector to receive the amplified audio from
output 1.
L
Amp Output 1 (mono audio model, see figure 5) —Connect passive,
speakers to this 2-pole captive screw connector to receive the
amplified audio from output 1.
AMP OUTPUT
1
CLASS 2 WIRING
Figure 5. Mono Audio Amplified Output Blocks
M
S/PDIF Output 4 — Plug a compatible device into this RCA
S/PDIF
OUT
connector with a 75-ohm digital audio cable to receive digital
audio signal from the output 4 digital stream.
N
DMP Expansion Port and LED —
EXP
LINK
Expansion Port — Plug an STP cable between this port
and the Expansion port on an optional Extron DMP 128
ProDSP Digital Matrix Processor.
Link LED — Lights to indicate that the port is connected to a
compatible device.