Setup guide

5DTP CrossPoint 84 IPCP • Installation DTP CrossPoint 84 IPCP • Installation4
Installation
This section describes installation of the DTP CrossPoint matrix switchers,
including connections and features. Topics that are covered include:
• Rear Panel
• Front Panel
Rear Panel
50-60 Hz
100-240V ~
2.0 A MAX
1
L
R
SIG LINK
OUT
SIG LINK
OUT
1
3
4
4
XTP
RS-232 IR
Tx Rx RTSCTS GTxRxG Tx Rx G
RS-232 IR
Tx Rx Tx RxG
Tx Rx G
Tx Rx Tx Rx
XTP
RESET
S/PDIF
OUT
DTP
XTP
DTP
XTP
DTP
EXP
+48V
MIC/LINE
1
1
3
2
4
2
3
4
LINK
LAN 2
LAN 1
LAN 3
HDBT
G
DTP
HDBT
2
1234
5
7
8
6
DTP CROSSPOINT 84
4
CLASS 2 WIRING
8/
R
RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
REMOTE
SIG LINK
IN
SIG LINK
IN
AUDIO INPUTS
AUDIO OUTPUTS
AMP OUTPUT
CONTROL
1234G
DIGITAL I/OCOM 3COM 2COM 1
S
DMP EXPANSION
SGG
1
1
2
2
C34C
INPUTS
-S G+S+V
PWR OUT = 6W
OUTPUTS
RS-232 IR
Tx Rx Tx RxG
1
LR
1
LR
3
LR
3
LR
5
LR
2
LR
4
LR
2
LR
4
LR
6
LR
IR/SERIAL eBUSRELAY S
BB NN
FFEE EEMM RRSS KKFF
CC
BB
CCAA OO GG HH
II
JJTT
DD
PP QQ
Figure 2. DTP CrossPoint 84 IPCP SA Switcher Rear Panel
ATTENTION:
• Remove system power before making all connections.
• Débranchez l’alimentation du système avant de faire n’importe
quelle connexion.
NOTE:
L
, below, is on the mono audio versions of the switcher and
is shown on figure 5, on page 7. It is in the same location on the
switcher as
K
, in figure 2.
A
HDMI Inputs 1 – 6 (see page 5)
K
Amp Output 1 (SA model) (see page 7)
B
Input TP switches (see page 5)
L
Amp Output 1 (MA model ) (see page 7)
C
DTP Inputs 7 – 8 (see page 5)
M
S/PDIF Output 4 (see page 7)
D
HDMI Output 1 – 2 (see page 6)
N
Expansion Port (see page 7)
E
Output TP switches (see page 6)
O
Over TP (Inputs 7 – 8) Ports (see page 8)
F
DTP Outputs 3 – 4 (see page 6)
P
Over TP (Outputs 3 – 4) Ports (see page 8)
G
Audio Inputs 1 – 6 (see page 7)
Q
IPCP Pro 350 processor (see page 8)
H
Mic/Line Inputs 1 – 4 (see page 7)
R
Remote Port (see page 8)
I
+48 V LEDs (see page 7)
S
Switcher Reset button (see page 8)
J
Audio Outputs 1 – 4 (see page 7)
T
Power connector (see page 8)
Video Inputs and Outputs
A
HDMI Inputs 1 through 6 — Plug HDMI digital video (or DVI
with appropriate adapters) into these HDMI ports. See HDMI
connectors on page 9 to secure the connector to the board
with a LockIt HDMI Cable Lacing Bracket.
B
TP (XTP/DTP) switches, inputs 7 and 8 —
XTP
DTP
ATTENTION:
• Position this switch BEFORE connecting the appropriate
device to the TP connector. Failure to comply can
damage the endpoint.
• Positionnez le sélecteur AVANT de connecter l’appareil
approprié au connecteur TP. Ne pas respecter cette
procédure pourrait endommager le point de connexion.
XTP position — Select if the transmitting device is an Extron
XTP matrix switcher. The input is HDMI with embedded audio plus
RS-232 and IR.
DTP position — Select if the transmitting device is an Extron DTP
device. The input is HDMI with embedded audio, analog audio,
RS-232 and IR, and remote power.
C
TP Inputs 7 and 8 — Plug compatible Extron DTP or XTP
SIG LINK
IN
signals into these RJ-45 ports using STP cables. See TP
connectors on page 10 to wire the connectors.
ATTENTION:
• Do not connect this port to a computer data or
telecommunications network.
• Ne connectez pas ces port à des données informatiques ou
à un réseau de télécommunications.