Setup guide
Table Of Contents
- DTP CrossPoint 84 IPCP
- Safety Instructions
- FCC Class A Notice
- Contents
- Introduction
- Installation
- Front Panel Operations
- Remote Control
- Selected SIS Commands
- Establishing a Network (Ethernet) Connection
- Number of Connections
- Establishing a USB Port Connection
- Host-to-Switcher Instructions
- Common SIS Command Symbols
- SIS Command and Response Table for Matrix Switcher Commands
- Installing and Starting the Control Programs
- Starting the Product Configuration Software
- Starting the DSP Configurator Program
- Accessing the HTML Pages
- Selected SIS Commands
- Extron Warranty
- Contact Info
24 DTP CrossPoint 84 IPCP • Remote Control 25DTP CrossPoint 84 IPCP • Remote Control
Command SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional Description
Recall a preset
Recall a preset
X1#
. Rpr
X1#]
Recall preset
X1#
.
View video and audio mutes
View output mutes
E
VM
} X1$
1
X1$
2
...
X1$
4
]
Each
X1$
response is the mute status of an output, starting
from output 1.
Example:
E
VM
}
0221
]
Output 1 is unmuted. Audio is muted on outputs 2 and 3,
video is muted on output 4.
Lock (Executive) modes
NOTE: See Setting the Front Panel Locks (Executive Modes) on page 17 for more information on the Lock modes.
Lock all front panel functions
1X
Exe1
]
Enable Lock mode 1.
Lock advanced front panel functions
2X
Exe2
]
Enable Lock mode 2.
Unlock all front panel functions
0X
Exe0
]
Enable Lock mode 0.
View lock status
X
X1%]
Information requests
Information request
I
DTPCP84
]
Request part number
N
60-
nnnn
-
nn
]
See the Extron website for part number.
Query rmware version
Q
X1^]
Example:
Q
1.23
]
The factory-installed controller rmware version is 1.23
(sample value only).
NOTE:
X1#
= Preset 01 through 32
X1$
= Video and audio mute status 0 = no mutes 2 = audio mute
1 = video mute 3 = video and audio mute
X1%
= Lock mode 0 = lock mode 0 (unlocked) 1 = lock mode 1 2 = lock mode 2 (default)
X1^
= Firmware version number to second decimal place (x.xx)
Installing and Starting the Control Programs
Several useful Windows-based programs are available on the Extron
website, including the Digital Signal Processor (DSP) Congurator
program, the Product Conguration Software (PCS), and the Firmware
Loader program.
The Product Conguration Software congures the video functions of the
switcher.
The DSP Congurator program is required for full operation of the
DSP functions of the switchers and to save presets. It also provides
some limited control of the non-DSP functions of the switcher. See
the DTP Crosspoint 84 User Guide and the program Help le for more
information.
Run either program from a PC connected to an Ethernet port on the
IPCP control processor (item
Q on page 8), serial port (item R on
page 8), or USB port (item A on page 14) on the switcher.
NOTES:
• For details on operating the program, see the DTP CrossPoint 84
Switcher User Guide.
• The DSP Congurator program has a software switch that allows
you to lock out audio adjustments in the Product Congurator
Software, making them unavailable for selection.
Installing the programs
The DSP Congurator, version 2.6 or newer; PCS, version 2.0 or newer;
and Firmware Loader are available on the Extron website. Download and
install all programs as follows:
1. Visit www.extron.com and click the Download tab.
1111111111
22
22222222
2. Click the Software link.
3. Select the desired software to download and click Download.
TIP: Jump to the nearest page of downloads by clicking the
desired filtering letter.
3333333333
The Download Center dialog box appears (see figure 12, on the next
page).