Setup guide

22 DTP CrossPoint 84 IPCP • Remote Control 23DTP CrossPoint 84 IPCP • Remote Control
Command SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional Description
HDCP status
View input HDCP status
E
I
X!
HDCP
} X$]
View HDCP status of all inputs
E
I*HDCP
} X$
1
X$
2
X$
3
...
X$
8
]
View output HDCP status
E
O
X@
HDCP
} X%]
View HDCP status of all outputs
E
O*HDCP
} X%
1
X%
2
X%
3
X%
4
]
Input reports as an HDCP-authorized device
HDCP authorized device on
E
E
X!
*1HDCP
}
HdcpE
X!
*1
]
Set the input as an HDCP authorized device.
HDCP authorized device off
E
E
X!
*0HDCP
}
HdcpE
X!
*0
]
Set the input as not an HDCP authorized device.
View HDCP authorized status
E
E
X!
HDCP
} X^]
Show HDCP authorized device status.
Execute Auto-Image
Execute Auto-Image
X&
*A Img
X&]
List Digital Sync Validation Processing (DSVP)
List sync of all inputs
0LS
X*
1
X*
2
X*
3
...
X*
8
]
Eight
X*
s; each is the signal status of an input, starting from
input 1.
Example:
0LS
Input:
Response Status:
no input detected
input detected
1 2345
6
78
0 0 0 1 1 1 0 0
NOTE:
X!
= Input number 01 – 08
X@
= Output number 01 – 04
X$
= HDCP status (for inputs) 0 = no source connected 1 = source is HDCP compliant 2 = source is not HDCP compliant
X%
= HDCP status (for outputs) 0 = No monitor connected
1 = Monitor connected but does not support HDCP
2 = Monitor connected, supports HDCP, but the video signal is not encrypted
7 = Monitor connected, supports HDCP, and the video signal is encrypted
X^ = HDCP authorized device 0 = off 1 = on (default)
X& = TP (scaled) output number 03 or 04
X*
= Signal detection status 0 = no input connected 1 = input connected
Command SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional Description
Input audio selection
Input audio selection
E
I
X!
*
X(
AFMT
}
AfmtI
X!
*
X(]
Example:
E
I1*0AFMT
}
AfmtI1*0
]
Auto (0): Digital audio takes priority over analog audio.
View input audio selection
E
I
X!
AFMT
} X(]
View input audio all selections
E
IAFMT
} X(
1
X(
2
X(
3
...
X(
8
]
Each
X(
is the auto, analog, or HDMI selection of an audio
input, starting at input 1.
Group master level (volume and mute)
NOTES: • The DTP CrossPoint 84 has 16 congurable group masters.
• By factory default, group 1 controls the program volume and group 2 controls the mic volume.
• Other group masters (such as mutes) must have been created in the DSP Congurator program to be available as
X1)
s for SIS commands.
Set gain (+) or attenuation (−) dB
value
E
D
X1)
*±
X1!
GRPM
}
GrpmD
X1)
*
X1!]
Specify + for gain or - for attenuation.
Example:
E
D1*+50GRPM
}
GrpmD1*50
]
Specify 5 dB level for group 1 (program volume).
Increment dB value
E
D
X1)
*
X1!
+GRPM
}
GrpmD
X1)
*
X1!]
Increase master
X1)
by
X1!
.
Example:
E
D1*75+GRPM
}
GrpmD1*125
]
Increase group 1 (program volume) by
7
.
5
dB (to
12
.
5
dB).
Decrement dB value
E
D
X1)
*
X1!
−GRPM
}
GrpmD
X1)
*
X1!]
Decrease master
X1)
by
X1!
.
View master value
E
D
X1)
GRPM
} X1!]
Set mute or unmute
E
D
X1)
*
X#
GRPM
}
GrpmD
X1)
*
X#]
Mute (
1
) or unmute (
0
) the group.
NOTE:
X!
= Input number 01 – 08
X#
= Mute 0 = off (unmuted) 1 = on (muted)
X(
= Input audio source 0 = Auto (see the example above) 2 = Analog (local 2-channel audio)
1 = HDMI (de-embedded digital audio) (default)
X1)
= Group number 01 – 16 (can be a user-dened alias enclosed in brackets {})
X1!
= Group master value dB value in 0.1 increments. Example:
X1!
= 50 = 5 dB.