Setup Guide Matrix Switchers DTP CrossPoint 84 IPCP Scaling Presentation Matrix Switchers with DTP Extension 68-2349-50 Rev.
Safety Instructions Safety Instructions • English WARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. ATTENTION: This symbol, , when used on the product, is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment.
Conventions Used in this Guide Notifications Contents The following are used: ATTENTION: • Risk of property damage. • Risque de dommages matériels. NOTE: A note draws attention to important information.
Introduction This section gives an overview of the Extron DTP CrossPoint 84 IPCP Series matrix switchers and describes their features. Topics that are covered include: •• About this Guide •• About the DTP CrossPoint Matrix Switchers About this Guide NOTE: For more information on subjects in this guide, see the DTP CrossPoint 84 IPCP Series User Guide and the IPCP Pro Series User Guide available at www.extron.com.
Flat Panel Display DTP Input and Output Signals Flat Panel Display The DTP inputs and outputs are proprietary signals that are created within any of the Extron DTP Extenders systems and transmitted over a single shielded twisted pair (STP) cable.
Installation Video Inputs and Outputs A HDMI Inputs 1 through 6 — Plug HDMI digital video (or DVI with appropriate adapters) into these HDMI ports. See HDMI connectors on page 9 to secure the connector to the board with a LockIt HDMI Cable Lacing Bracket. This section describes installation of the DTP CrossPoint matrix switchers, including connections and features.
XTP OUT LINK XTP Tx Rx G Tx Rx OUT DTP 4 S/PDIF OUT 8 4 S/PDIF OUT HDBT REMOTE RESET Tx Rx G Video Output Features with appropriate adapters) into these ports. See HDMI connectors on page 9 to secure the connector to the board with a LockIt HDMI Cable Lacing Bracket. ATTENTION: • Figure 4. HDBT DTP L 1 2 R L R L 3 4 R L R L 5 6 R 1 2 R 3 1 MIC/LINE 2 3 4 4 L L 1 2 R L R L 3 4 R R Video Output Features stereo audio inputs into these 3.
Serial and IR Insertion Connections OUTPUTS RS-232 1 2 3 SIG HDBT SIG OVER TP RS-232 DTP 4 Tx Rx G Tx Rx LINK XTP OUT LINK XTP IR DTP OUT Tx Rx G Tx Rx HDMI connectors 4 S/PDIF OUT 3 5 4 6 SIG LINK XTP DTP Figure 6. IR 8 Tx Rx G Tx Rx INPUTS 2 OVER TP RS-232 IN Use a LockIt Lacing Bracket to securely fasten each HDMI cable to the switcher as follows. HDBT RS-232 1 Additional Connector Information IR SIG LINK XTP IR Tx Rx G Tx Rx IN 1.
TP connectors LAN ports All RJ-45 ports, whether DTP ports, the Expansion port, and the LAN (Ethernet) ports on the IPCP control processor use twisted pair cables (see figure 8). The LAN ports require Category (CAT) 3, CAT 5e, or CAT 6a unshielded twisted pair (UTP) or shielded twisted pair (STP) cables, crossover or patch cables. •• Patch (straight) cable — The cable used depends on your network speed.
For the DTP ports only — Local and Mic/line audio connectors Extron recommends the following practices to achieve full transmission distances up to 330 feet (100 m) and reduce transmission errors. Use the supplied tie-wrap to strap the audio cable to the extended tail of the connector.
Front Panel Operations Front Panel INPUTS 1 2 3 4 5 1 2 3 4 6 7 8 CONFIG This section describes simple DTP CrossPoint matrix switcher operation from the front panel. Topics that are covered include: •• Creating a Tie OUTPUTS •• Recalling a Preset Extron A Figure 11.
Recalling a Preset Setting the Front Panel Locks (Executive Modes) A "preset" is a configuration that has been stored. The matrix switcher has three levels of front panel security lock that limit the operation of the switcher from the front panel. The three levels are: 1. Press and release the Preset button. Recall a preset •• Lock mode 0 — The front panel is completely unlocked. PRESET PRESET Press and release.
Remote Control Selecting Lock Mode 2 or Toggling Between Mode 2 and Mode 1 NOTES: • If the switcher is in Lock mode 0 or mode 1, this procedure selects mode 2. The Esc, Video, and Audio buttons flash twice. • If the switcher is in Lock mode 2, this procedure selects mode 1. The Video and Audio buttons flash twice. This section describes using the remote control features of the DTP CrossPoint matrix switchers to control the devices.
20 DTP CrossPoint 84 IPCP • Remote Control 2 = video and sync muted 1 = video muted Vmt1] Vmt0] 00 – 08 (00 = untied) 01 – 04 0 = off (unmuted) X! = Input number X@ = Output number X# = Mute NOTE: X#] 1*B 0*B Video only mute Video and sync mute Video unmute Read video mute Global video mute Global video unmute X@*1B X@*2B X@*0B X@B VmtX@*1] VmtX@*2] VmtX@*0] Mute all video outputs. Unmute all video outputs. Mute output X@ video (sync remains active). Mute output X@ video and sync.
SIS Command and Response Table for Matrix Switcher Commands Command SIS Command (Host to Unit) Response (Unit to Host) Additional Description Create ties NOTES: • Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*02$03*03%4*4$. • The matrix switchers support 1- and 2-digit numeric entries (1*1! or 02*02%). • Audio breakaway command functions are dependent on the audio routing selections of the inputs and outputs.
22 Command SIS Command DTP CrossPoint 84 IPCP • Remote Control (Host to Unit) Response (Unit to Host) Additional Description HDCP status View input HDCP status View HDCP status of all inputs View output HDCP status View HDCP status of all outputs EIX!HDCP} EI*HDCP} EOX@HDCP} EO*HDCP} X$] X$1X$2X$3 ...
24 View video and audio mutes X1#. RprX1#] Recall preset X1#. View output mutes EVM} X1$1X1$2... X1$4] Each X1$ response is the mute status of an output, starting from output 1. Example: EVM} 0221] Output 1 is unmuted. Audio is muted on outputs 2 and 3, video is muted on output 4. Information requests The factory-installed controller firmware version is 1.23 (sample value only). Exe1] Enable Lock mode 1. Exe2] Enable Lock mode 2.
Installing and Starting the Control Programs Several useful Windows-based programs are available on the Extron website, including the Digital Signal Processor (DSP) Configurator program, the Product Configuration Software (PCS), and the Firmware Loader program. The Product Configuration Software configures the video functions of the switcher. The DSP Configurator program is required for full operation of the DSP functions of the switchers and to save presets.
1 4 2 Figure 13. Device Discovery Screen 5 Figure 12. Download Center Dialog Box 4. Enter the requested personal information; TIP: Click Remember Me to eliminate step 4 in future downloads. 5. Click Download to copy the software or firmware to your computer. The download warns you about downloads and asks you to confirm it. TIP: You can also launch the Product Configuration Software from the DSP Configurator program, BUT PCS can be locked out from within DSP. 2.
Starting the DSP Configurator Program The DSP Configurator can connect to the switcher via any rear panel LAN port, the rear panel Remote (RS-232) port, or the front panel Configuration port. The program can operate at 9600, 19200, 38400, or 115200 baud rates for the Remote port. NOTE: Extron recommends connection via an Ethernet LAN port for the DSP Configurator program. Start the DSP Configurator program, as follows: 1. Click Start > Programs > Extron Electronics > DSP Configurator > DSP Configurator.
Accessing the HTML Pages 3. Press the keyboard key. The switcher checks whether it is password-protected. NOTES: If the switcher is not password-protected, it checks and downloads the HTML start-up page. The switcher is ready for operation via HTML remote control. • • If your Ethernet connection to the matrix switcher is unstable, try turning off the proxy server in your web browser.
Extron Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase.
Extron USA Headquarters +800.633.9876 (Inside USA/Canada Only) Extron USA - West +1.714.491.1500 +1.714.491.1517 FAX Extron Asia +800.7339.8766 Inside Asia Only Extron USA - East +1.919.850.1000 +1.919.850.1001 FAX Extron Middle East +971.4.2991800 +971.4.2991880 FAX Extron Europe +800.3987.6673 (Inside Europe Only) +31.33.453.4040 +31.33.453.4050 FAX Extron India 1800.3070.3777 (Inside India Only) +91-80 3055.3777 +91 80 3055 3737 FAX Extron Japan +81.3.3511.7655 +81.3.3511.
