User’s Manual CPM200 AND CPM208 www.extron.com Extron Electronics, USA Extron Electronics, Europe Extron Electronics, Asia Extron Electronics, Japan 1230 South Lewis Street Anaheim, CA 92805 USA 714.491.1500 Fax 714.491.1517 Beeldschermweg 6C 3821 AH Amersfoort The Netherlands +31.33.453.4040 Fax +31.33.453.4050 135 Joo Seng Road, #04-01 PM Industrial Building Singapore 368363 +65.6383.4400 Fax +65.6383.4664 Kyodo Building 16 Ichibancho Chiyoda-ku, Tokyo 102-0082 Japan +81.3.3511.7655 Fax +81.3.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
Precautions 安全须知 • 中文 这个符号提示用户该设备用户手册中 有重要的操作和维护说明。 这个符号警告用户该设备机壳内有 露的危险电压，有触电危险。 注意 阅读说明书 • 用户使用该设备前必须阅读并理解所有 安全和使用说明。 保存说明书 • 用户应保存安全说明书以备将来使用。 遵守警告 • 用户应遵守产品和用户指南上的所有安全 和操作说明。 避免追加 • 不要使用该产品厂商没有推荐的工具或追 加设备，以避免危险。 Table of Contents 警告 电源 • 该设备只能使用产品上标明的电源。 设备必须 使用有地线的供电系统供电。 第三条线（地线）是 安全设施，不能不用或跳过 。 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设 备后或桌面电源的电源线，或任何接到市电系统 的电源线。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 维护 • 所有维修必须由认证的维修人员进行。 设备内 部没有用户可以更换的零件。为避免出现触电危险 不要自己试图打开设备盖子维修该设备。 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来 防止机内敏感元件过热。 不要用任何东西挡住通 风孔。 锂电池
Table of Contents, cont’d CMP200 and CMP208 1 Chapter One Introduction About the Modular A/V Connector Bays Features ii CPM200 and CPM208 • Table of Contents
Introduction About the Modular A/V Connector Bays The Extron CPM200 and CPM208 are table-mounted, architectural solutions for inconspicuous computer video, audio, phone, data, and control interface connector access and control.
Introduction, cont'd CMP200 and CMP208 2 Chapter Two Installation Installing the CPM Enclosure Preparing the Table Installing the CPM Enclosure Installing the MAAPs and the Cables 1-4 CMP200 and CMP208 • Introduction
Installation Installation Overview Install and set up a CPM modular A/V connector bay as follows: 1 Draw a mounting template, based on the surface cut-out dimensions shown in the back of this guide (see Appendix A). 2 Place the template where you want the enclosure installed, and mark the surface material to be removed. 3 Cut a hole in the surface where the enclosure will be installed and install the enclosure. The screw clamps secure the enclosure to the tabletop.
Installation, cont'd Installing the CPM Enclosure 4. 1. Remove the mounting brackets (2 on the CPM200 and 4 on the CPM208) on the sides of the enclosure. 2. If necessary, move the MAAP shelves to the lower position (optional) from the upper (default) position within the CPM unit. See the section on "Installing the MAAPs and the Cables" on the following page. The upper position is designed for applications using A/V and active connector MAAP modules.
Installation, cont’d 3. Reinstall the screws to secure the MAAP shelves in the lower position within the enclosure. Installing and cabling the MAAPs Once the MAAP shelf is installed in the selected position, install the cables and MAAPs in the CPM enclosure by connecting the appropriate cable to the back side of each MAAP module, or installing the cable in the split (cable slot) module, then installing each MAAP module on the MAAP shelf.
Maintenance and Modifications Removing and Replacing the Enclosure Remove and replace the CPM enclosure for maintenance as follows: Ensure that any AC power (if connected) is disconnected before removing the CPM unit. 1. Loosen and remove the screws holding the MAAP module in the CPM enclosure. 2. Gently pull the MAAP module, with the cables attached, out of the CPM enclosure. 3. Remove the cables from the MAAPs. 4.
Reference Information Specifications Top Plate Dimensions The cutout dimension illustrations (figures A-1 and A-2) are not to scale and are for reference only. The dimensions shown in the illustrations will help you prepare a mounting template. The surface cutout area is shown as a shaded area on the diagrams and the cutout dimensions are provided. General Rack mount .................................... No, but furniture mountable Enclosure type ...............................
Reference Information, cont'd 2.56" Cut-Out Template for Extron's 4.00" 0.45" CPM208 3 A/V Modular Plates Lid Access Slot 2.57" 4.00" 6.75" (17.1 cm) top view (lid closed) Top View (lid open) 99 1.97" 5.88" (14.9 cm) 4.00" 4.75" (12.1 cm) 0.50" (min.) 1.00 " 3.50" 3.63" (9.2 cm) 0.10" 2.50 " SURFACE CUT-OUT AREA = 5.88"(14.9 cm) x Modular A/V Connector Plate in Upper Position Table Top Thickness Range: 0.50" to 2.50" 2.50" (max.) 2.
Reference Information, cont'd 6.75" 6.75" 4.75" 4.75" Top View (lid closed) Top View (lid open) 1.97" 99 Table top thickness range: 0.50" to 2.50" 6.75" 0.50" (min) 1.00 " 3.50" Modular A/V Connector Plate in upper position 2.50 " 2.50" Anti-rotation Bumper, 4 Places Modular A/V Connector Plate in lower position 5.25" 2.50" Thumbscrews 4 Places 1.
