CIA101 COMPUTER INTERFACE WITH INTERNAL POWER SUPPLY CIA101 OPERATION MANUAL
Installation and Safety Instructions For Models without a Power Switch: The socket outlet shall be installed near the equipment and shall be accessible. For all Models: No serviceable parts inside the unit. Refer service to a qualified technician. For Models with Internal or External Fuses: For continued protection against fire hazard, replace only with same type and rating of fuse.
1 Product Overview DESCRIPTION The CIA101 is a high-performance computer interface for analog video and stereo audio signals. The unit is compatible with a variety of analog signals including VGA, SVGA, XGA, SXGA, UXGA, MAC, SUN, SGI and other high-resolution workstations. The CIA101’s compact design allows users to place it in a variety of locations or permanently mount it to virtually any flat surface (using the optional L mounting brackets).
2 • Sharpness Control - provides effective image enhancement for high-resolution video signals by increasing clarity and image detail, and may be used to compensate for signal loss due to long cable runs. • Hum Suppression Capability - removes visible effects caused by video ground loops that exist between the signal source and the interface.
3 Installation This section offers step-by-step instructions for installing the CIA101. An Application Diagram is provided on page 5, and Front and Rear Panel Connector and Control Diagrams are on page 6. Read the instructions carefully before initiating the installation procedure. Before you begin, make sure that there is no power connected to any components in the display system, and that all the power buttons are off. 1.) Place / install the CIA101 at the desired location.
4 7.) Connect the computer sound card output (if applicable) to the CIA101 3.5mm female stereo audio input connector using an IN8200M-1 Series cable [15-pin HD with 3.5mm (M-M) mini DIN], or an IN9106 audio patch cable (3.5mm stereo mini male to 3.5mm stereo mini male). For computers with RCA connectors, use the IN9107 audio adapter cable [(1) 3.5mm stereo mini male to (2) RCA male]. 8.) Connect the local computer monitor (if applicable) to the local monitor output port of the CIA101.
©2001 - INLINE, Inc. CIA101 Operation Manual - V1.
6 CIA101 FRONT PANEL CONNECTORS AND CONTROLS Horizontal Position Control Monitor Emulation with LED Indicator Local Monitor Output Power Indicator Stereo Audio Input Video Input CIA101 REAR PANEL CONNECTORS AND CONTROLS Dip Switches Audio Output Connector ( Balanced or Unbalanced ) Sharpness Control Video Output Connectors CIA101 Operation Manual - V1.3 01/03/01 Power Connector ©2001 - INLINE, Inc.
7 HORIZONTAL POSITION CONTROL The location of the horizontal position control is shown in the Front Panel Connectors and Controls diagram on the previous page. Press and release the rocker button to shift the image by one step to the left or right. Press and hold the button to shift the image continuously. Note: The horizontal position control has no effect on the local computer monitor.
8 DIPSWITCH SETTINGS Most installations will not require any changes to the dipswitch settings. The factory default and specialized dipswitch settings are indicated below.
9 Specifications CIA101 Computer Interface Input Connector Type RGB Video Signals Input Impedance Sync Signals Horizontal Scan Rate Vertical Sync Range Stereo Audio Connector Stereo Audio Compatibility Output Local Monitor (Buffered) Main Output Output Signal Formats RGB Signals Bandwidth Audio Output Connector Main Audio Output Dimensions Size (including faceplate) Product Weight Shipping Weight Power Power Supply Regulatory Compliance Safety EMI (1) 15-pin HD female - standard VGA pin-outs Analog, 1.
10 Optional Accessories Audio Input Cables: IN9106: 3.5mm stereo mini male to 3.5mm stereo mini male, 6’ long IN9107: (1) 3.
11 Problem: The power switch is turned on, but the front panel power LED is dark. Solution 1: Make sure the IN9230 IEC power cable is securely plugged into the unit and the A/C source. Solution 2: Make sure the A/C source is live. Solution 3: The CIA101 contains a 0.125A / 250V time delay fuse. To change the fuse, remove the power cable, then slide out the fuse holder (located on the rear panel between the power switch and the IEC cable receptacle) using the IN9339 adjustment tool.
12 Warranty ♦ INLINE warrants the equipment it manufactures to be free from defects in materials and workmanship. ♦ If equipment fails because of such defects and INLINE is notified within two (2) years from the date of shipment, INLINE will, at its option, repair or replace the equipment at its plant, provided that the equipment has not been subjected to mechanical, electrical or other abuse or modifications.
