CIA100 COMPUTER INTERFACE CIA100 OPERATION MANUAL
Installation and Safety Instructions For Models without a Power Switch: The socket outlet shall be installed near the equipment and shall be accessible. For all Models: No serviceable parts inside the unit. Refer service to a qualified technician. For Models with Internal or External Fuses: For continued protection against fire hazard, replace only with same type and rating of fuse.
1 Product Overview DESCRIPTION The CIA100 is a high-performance computer video interface for analog video signals including VGA, SVGA, XGA, SXGA, UXGA, MAC, SUN and other high-resolution workstations. The CIA100’s compact design allows users to place it in a variety of locations or permanently mount it to virtually any flat surface (using the optional IN9250 mounting brackets).
2 Compatibility INPUT The CIA100 will accept high-resolution video signals from virtually any computer that outputs an analog video signal. The unit will work with signals at virtually any resolution and refresh rate. Compatible computer video signals include VGA, SVGA, XGA, SXGA, UXGA, MAC, SUN, SGI and other high-resolution computers outputting an analog video signal. Input signal compatibility parameters are listed below.
3 Installation This section offers step-by-step instructions for installing the CIA100. An Application Diagram is provided on page 5, and Front and Rear Panel Connector and Control Diagrams are on page 6. Note: Read the instructions carefully before initiating the installation procedure. Before you begin, make sure that there is no power connected to any components in the display system, and that all the power buttons are off. 1.
4 7.) Apply power to the CIA100 using the IN9205 9 VDC; 1.0A power supply (included). The power LED on the front of the unit will illuminate. 8.) Complete the installation by turning the computer and computer monitor on. If required, adjust the horizontal position control to center the image on the data display device (see the Horizontal Position Control Section on page 7 for more details).
©2001 - INLINE, Inc. CIA100 Operation Manual - V1.
6 CIA100 FRONT PANEL CONNECTORS AND CONTROLS Horizontal Position Control Monitor Emulation with LED Indicator Video Input Local Monitor Output Power Indicator CIA100 REAR PANEL CONNECTORS AND CONTROLS Dip Switches Power Connector Video Output Connectors CIA100 Operation Manual - V1.3 01/03/01 ©2001 - INLINE, Inc.
7 HORIZONTAL POSITION CONTROL The location of the horizontal position control is shown in the Front Panel Connectors and Controls Diagram on the previous page. Press and release the rocker button to shift the image by one step to the left or right. Press and hold the button to shift the image continuously. Note: The horizontal position control has no effect on the local computer monitor.
8 MONITOR EMULATION The factory default setting for the CIA100 is Monitor Emulation Enabled. If the application requires a local monitor, make sure that the front panel Monitor Emulation LED is OFF (press the MONITOR EMULATION Button to toggle between enabled / disabled). If no local monitor is necessary, make sure the Monitor Emulation LED is ON.
9 Specifications CIA100 Computer Interface Input Connector Type RGB Video Signals Input Impedance Sync Signals Horizontal Scan Rate Vertical Sync Range Output Local Monitor (Buffered) Main Output Output Signal Formats RGB Signals Bandwidth Dimensions Size (including faceplate) Product Weight Shipping Weight Power Power Supply Regulatory Compliance Safety EMI (1) 15-pin HD female - standard VGA pin-outs Analog, 1.5 Vp-p max.
10 Coaxial Cables Standard Resolution Standard Resolution, Plenum Super High Resolution Super High Resolution, Plenum Ultra High Resolution RGB Installation Cables 3-Conductor 4-Conductor IN7000-4 IN7000P-4 IN7300-3 IN7300-4 IN7200-3 IN7200-5 5-Conductor IN7000-5 IN7000P-5 IN7300-5 IN7400P-5 IN7200-6 All cable grades are available in lengths from 3’ to 250’ pre-terminated with high quality BNC connectors or as bulk cable.
11 Problem: Solution: Possibly the RGBS or RGBHV cable is bad. Try switching connections on the output to verify that the bad color’s cable is OK (Example: If there is no red, try running the green output through the red cable and see if the green is displayed or not). Problem: The horizontal position control is not working. Solution 1: Check the dipswitch settings to see if the horizontal position control has been disabled. Solution 2: The input signal may be RGsB (sync on green).
12 Warranty ♦ INLINE warrants the equipment it manufactures to be free from defects in materials and workmanship. ♦ If equipment fails because of such defects and INLINE is notified within two (2) years from the date of shipment, INLINE will, at its option, repair or replace the equipment at its plant, provided that the equipment has not been subjected to mechanical, electrical or other abuse or modifications.
