CD100 COURT DIRECTOR™ COURTROOM A / V SWITCHING SYSTEM CD100 COURT DIRECTOR™ COURTROOM A/V SWITCHING SYSTEM CD110 COURT DIRECTOR™ STATUS DISPLAY BUTTON (OPTIONAL) CD100 OPERATION MANUAL
Installation and Safety Instructions For Models without a Power Switch: The socket outlet shall be installed near the equipment and shall be accessible. For all Models: No serviceable parts inside the unit. Refer service to a qualified technician. For Models with Internal or External Fuses: For continued protection against fire hazard, replace only with same type and rating of fuse.
1 Product Overview DESCRIPTION The CD100 Court Director™ System is a complete A/V switching and distribution solution for courtroom evidence presentation. By combining A/V signal switching, distribution and control into one product, the CD100 Court Director™ simplifies the design and installation process for system designers and integrators, offering flexible signal routing capabilities and easy operation for a variety of courtroom and audiovisual system applications.
2 Compatibility The CD100 Court Director features 15-pin HD female input and output connectors and connects directly to PC, Mac and SGI graphics ports and local monitors that have 15-Pin HD connectors using high-resolution coaxial VGA extension / adapter cables. The unit can also be connected to Mac, SUN, SGI and 4 or 5 BNC workstations using the appropriate input / output adapter cables. All input / output connectors are located on the back of the CD100.
3 Installation OVERVIEW This section offers step-by-step instructions for installing the Court Director System. An Application Diagram is provided on page 6. Note: Read the instructions carefully before initiating the installation procedure. Before you begin, make sure that there is no power connected to the system, and that all the power buttons are off. The VGA input / output connectors on the rear of the CD100 are all labeled.
4 4.) Connect the Audio Output Cables - to the appropriate pins on the CD100 5-pin Phoenix connector. Make sure that the stereo audio output is connected appropriately for a balanced or unbalanced signal as required by the installation (see the diagram below). 5LJKW /HIW *URXQG /HIW 5LJKW *URXQG /HIW *URXQG 5LJKW 5LJKW %DODQFHG 5LJKW *URXQG 8QEDODQFHG Unbalanced Output - connect to the Left, Right and Ground connectors.
5 ADAPTER / EXTENSION CABLES FOR INPUT AND LOCAL MONITOR OUTPUT The CD100 has 15-pin HD VGA-type input and local monitor output connector ports. The following cables / adapters are available: Computer 3’ 6’ 12’ VGA: 15-Pin HD Input Cable (M-M) IN8003M-1 IN8006M-1 IN8012M-1 Output Cable (M-F) IN8006-1 IN8012-1 VGA with Stereo Audio: 15-Pin HD with 3.
6 CD100 / CD110 Court Director™ System Operation Manual - V. 1.0 11/30/00 © 2000 - INLINE, Inc.
7 INPUT 3: AUXILUARY A/V AUDIO IN - 15-pin HD female video input Left and Right RCA connectors AUDIO COUNSEL B JURY AUDIO R L + - GND - + OUT PUT STATUS JUDGE OVERRIDE RS-232 IN TX GND RX RS-232 OUT TX GND RX ! 90-260 VAC, 0.2A, 47-63HZ CD100 / CD110 Court Director™ System Operation Manual - V. 1.0 11/30/2000 90 -260 VAC; 0.
8 Operation MEMORY SELECT This section focuses on operating the CD100 / CD110 using the front panel controls and commands. All switching operations, audio adjustments and memory selections can be performed through the CD100 front panel or via RS-232 serial controls. Serial control information is provided on page 10. CD100 FRONT PANEL CONTROLS VOLUME MUTE AUDIO INPUT SELECT - Selects the audio and video source. The large buttons labeled Input 1 (Counsel A), Input 2 (Counsel B), and Input 3 (Aux.
9 To save a configuration, simply press the desired Memory Select Button and hold for five seconds. The LED below the button will illuminate. Pressing and releasing the button will recall the configuration. A memory setting can be deleted by either pressing and holding the button for five seconds, or replacing it with a new configuration by repeating the save process.
10 Factory Default Reset The CD100 allows users to reset all settings to factory default status. Factory default settings can be restored using the following procure: Press and hold the VOLUME DOWN Button while turning the unit’s power switch to ON. If power is already on, press and hold the VOLUME DOWN button and switch the power off, and then back on.
11 COMMAND CODE STRUCTURE AND DELIMITERS All commands sent to the CD100 must contain a leading code, the command code, and an ending code. Each command must be completely executed before the unit will accept a new command. The unit can be set to recognize six sets of leading and end codes (delimiters) when using an RS-232 remote: parentheses ( ), brackets [ ], braces{ }, slashes \ /, less and greater than < >, and signs !#. The factory default serial delimiters are [ ].
12 Command ACIA7 ACIA8 BALR BALL BAL@ BAL? BALxxx BAS+ BASBAS@ BASxxx BAS? CALLx CH1 CH2 CH3 CH@ CH? CDMCD0 CDMCD1 CDMCD2 CDMCD3 CDMCD4 CDMCD5 DISPLY0x DISPLY1x FP0 FP1 FP FP? INFO MUTE0 MUTE1 MUTE? OVER0 OVER1 OVER? PCCx Description set projector port baud baud rate to 19,200 set projector port baud baud rate to 38,400 increment balance of currently selected input channel decrement balance of currently selected input channel set audio balance of currently selected channel to center (016)** request balan
13 Command PCLxyyy PCE0 PCE1 PCE2 PCE? RES0 RES1 SAVEx TRE+ TRETRE@ TRE? TRExxx VOL+ VOLVOL@ VOL? VOLxxx Description load ascii projector code for projector memory x (1<=x<=4) (code yyy consists of 0 to 8 ascii characters) To allow inclusion of the current command code characters in the PCL ASCII string, the Data Link Escape character of ‘\’ may be used. If the character is supposed to be interpreted literally instead of by its command code definition, it is preceded by a ‘\’.
14 Specifications CD100 Court Director™ Input Video Connector Type RGB Video Signal Input Impedance Sync Signals Compatible Formats Control Connector Stereo Audio Input Output Buffered Local Monitor Main Output Output Format Control Connector Main Audio Output General RS-232 Control Power Supply Dimensions Shipping Weight Product Weight Regulatory Approvals (3) 15-pin HD female Analog, 1.5 Vp-p max. 75 ohms TTL compatible RGBHV / RGBS / RGsB DB-9 female 3.
15 Optional Accessories VGA Monitor Adapter and Extension Cables IN8000 Series: 15-pin HD male to 15-pin HD female, lengths from 3’ to 250’ IN8000M Series: 15-pin HD male to 15-pin HD male, lengths from 3’ to 250’ For Other Computers: Refer to the Adapter / Extension Cables Chart on page 5 Connector Cables IN9139 Series: Status Display Link Cable - Connects CD100 to CD110, 9-pin D Male to 9-pin D male (available in a variety of lengths) Audio Cables IN9106: 3.5mm stereo mini to 3.
16 Warranty • INLINE warrants the equipment it manufactures to be free from defects in materials and workmanship. • If equipment fails because of such defects and INLINE is notified within two (2) years from the date of shipment, INLINE will, at its option, repair or replace the equipment at its plant, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications.
