User’s Manual Cable Cubby® 200 Cable Cubby® 300C Cable Cubby® 300S Cable Cubby® 600 Cable Cubby® 800 Extron USA - West Headquarters +800.633.9876 Inside USA / Canada Only +1.714.491.1500 +1.714.491.1517 FAX Extron USA - East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East +800.633.9876 +800.3987.6673 +800.7339.8766 +81.3.3511.7655 +81.3.3511.7656 FAX +400.883.1568 +971.4.2991800 +971.4.2991880 FAX +1.919.863.1794 +1.919.863.1797 FAX +31.33.453.4040 +31.33.453.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
安全须知 • 中文 警告 这个符号提示用户该设备用户手册中 有重要的操作和维护说明。 电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 必须使用有地线的供电系统供电。 第三条线 （地线）是安全设施，不能不用或跳过。 这个符号警告用户该设备机壳内有暴 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后 或桌面电源的电源线，或任何接到市电系统的电源线。 露的危险电压，有触电危险。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 注意 阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理 解所有安全和使用说明。 保存说明书 • 用户应保存安全说明书以备将来使 用。 遵守警告 • 用户应遵守产品和用户指南上的所有安 全和操作说明。 避免追加 • 不要使用该产品厂商没有推荐的工具或 追加设备，以避免危险。 维护 • 所有维修必须由认证的维修人员进行。 设备内部没 有用户可以更换的零件。为避免出现触电危险不要自己 试图打开设备盖子维修该设备。 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止 机内敏感元件过热。 不要用任何东西挡住通风孔。
Table of Contents Chapter 1 • Introduction ........................................................... 1-1 About the Cable Cubby® Products ........................................ 1-2 Features ......................................................................................... 1-5 Chapter 2 • Installation .............................................................. 2-1 Installation Overview . .............................................................. 2-2 Preparing the Routing Template ..........
Table of Contents, cont’d Cable Cubby® Products 1 Chapter One Introduction About the Cable Cubby® Products Features 68-701-01 Rev. I 06 09 All trademarks mentioned in this manual are the properties of their respective owners.
Introduction About the Cable Cubby® Products • Cable Cubby 200 (all models) — Two single-space AAPs The Extron Cable Cubby products are furniture-mounted, architectural solutions for inconspicuous cable access and connection points. When cables are not in use, they can be stored out of the way while remaining connected to the presentation system. Most US/domestic Cable Cubby models provide two unswitched USA AC power outlets. The US/domestic Cable Cubby 200 provides one outlet.
Introduction, cont’d N The elevation and arrangement of the power outlet and AAPs in the Cable Cubby 200 are fixed and not customizable. The installed Cable Cubby fits nearly flush within a table or podium top, storing the AAPs and cables out of the way and out of sight. To access the AAPs and connectors, lift the lid (figure 1-2). Half-moon cutouts in the lid allow you to run cables in or out and then close the lid. For Cable Cubby 300s, 600s, and 800s, you can lower the lid into its recessed position.
Introduction, cont’d Cable Cubby® Products 2 Chapter Two Installation Installation Overview Preparing the Routing Template Preparing the Table Installing the Cables and AAPs Mounting the Cable Cubby 1-6 Cable Cubby® Products • Introduction
Installation Installation Overview Preparing the Routing Template Install and set up the Cable Cubby enclosures as follows: 1 If you plan to use a mounting template that has not been prepared, prepare the template. See "Preparing the Routing Template", on the next page. 2 Cut a hole in the surface where the enclosure will be installed. See "Preparing the Table", later in this chapter.
Installation, cont’d Preparing the Table The preferred and recommended method for preparing the table for square Cable Cubby models and one of two preferred methods for the Cable Cubby 300C is to use the appropriate Extron routing template and a router. W 4. For the Cable Cubby 300C, another preferred method is to use a 6" hole saw. C Wear safety glasses when operating the router. Failure to comply can result in eye injury.
Installation, cont’d Preparing the table with a hole saw (Cable Cubby 300C only) Prepare the table with a hole saw as follows: 1. On the tabletop or other installation surface, mark the 6" circle, then find and mark the center of the circle. W 2. Wear safety glasses when operating the drill. Failure to comply can result in eye injury. Using a portable drill with a 6" (or 152 mm) hole saw, carefully cut the opening in the table surface at the desired location (figure 2-3).
Installation, cont’d Installing the power module (CC 300, 600, and 800) From the underside of the Cable Cubby, gently push the power module into the desired position at the desired elevation. Secure the power module into position with four Phillips head screws. N The Universal AC outlet is fully compatible with Europlug, British, Indian, Danish, and Italian plug types. See the universal AC outlet guide on the Extron Web site, www.extron.com, for compatibility details on all plug types.
Installation, cont’d Installing the shelf assembly (CC 300, 600, and 800) From the underside of the Cable Cubby, gently push the AAP shelf assembly into the desired position at the desired elevation. Ensure there is enough space above the AAP assembly for the Cable Cubby lid to close completely. Secure the AAP shelf assembly into position with four Phillips head screws. If the AAP shelf assembly does not slide easily into the cubby, loosen the AAP mounting nuts.
Installation, cont’d 3. Carefully lower the Cable Cubby into the hole to test the fit. If necessary, remove the enclosure and use a file or rasp to enlarge or smooth the edges of the opening (figure 2-7). 8. Cable Cubby 200 — Use the four included #6 wood screws to secure the Cable Cubby 200 to the table (figure 2-8).
Installation, cont’d Cable Cubby® Products 3 Chapter Three Maintenance and Modifications Removing and Replacing the Cable Cubby Replacing Cables or an AAP Adding an Additional Power Module (CC 600, CC 800) 2-14 Cable Cubby® Products • Installation
Maintenance and Modifications The Cable Cubby can be modified after installation to change cables, to replace an AAP, or to add a second power module. These modifications may require removing the cubby from the table. Removing and Replacing the Cable Cubby You may need to remove the cubby from the table in which it is mounted to replace cables or AAPs, to adjust the height of the AAP assemblies, or to install a second power module.
Maintenance and Modifications, cont’d 4. Cable Cubby 200 — Remove the screws at the four corners that secure the cubby to the table (figure 3-2). 10. Cable Cubby 300, 600, and 800 — Snugly tighten the Phillips head screws on the screw clamps to secure the enclosure to the surface. 11. Cable Cubby 300, 600, and 800 — Tighten the locking thumbscrews on the screw clamps to lock the clamp in position. 12.
Maintenance and Modifications, cont’d Adding an Additional Power Module (CC 600 and CC 800) Figure 3-3 shows typical configurations before and after you add a second power module to an international Cable Cubby 600. Each additional power module occupies two (USA/domestic models) or three (international models) of the cubby’s AAP spaces, reducing the amount of AAP space available in the cubby for cable pass through (split) or passive AAPs.
Maintenance and Modifications, cont’d Cable Cubby 600 and 800 US/Domestic models — You probably do need replacement shelf brackets when you add a US/Domestic power module to a US/Domestic Cable Cubby, because the power module takes up two spaces in a cubby that, in its standard configuration, is equipped with three-space (Cable Cubby 600) or four-space (Cable Cubby 800) shelves.
Maintenance and Modifications, cont’d 4 From the underside of the Cable Cubby, gently push the additional power module into the desired position at the desired elevation. Secure the power module into position with the included four Phillips head screws (figure 3-7). Extron Cable Cubby 600 2 Screws ea. side Push module through bottom of enclosure. Secure in place with screws. Figure 3-7 — Installing the power module 5 6 If desired, assemble and install replacement AAP shelf assemblies.
Reference Information Specifications General Rack mount ������������������������������������ No, but furniture mountable Enclosure type ������������������������������ Metal H H Enclosure dimensions C N Use the appropriate metal Extron routing template or refer to the surface cutout dimensions here before cutting a hole in the furniture or other surface. Pay special attention to the direction the unit will face; the unit’s AAP and connector access side is underlined.
Reference Information, cont’d H H W D Cable Cubby 600 Cable Cubby 600 Top plate (outer rim) ������������������� Surface cutout (inside rim) ��������� Box (under surface) ��������������������� A-4 W D Cable Cubby 800 6.960" W x 6.960" D (17.68 cm W x 17.68 cm D) 6.460 ±0.0325" W x 6.460 ±0.0325" D (16.41 ±0.083 cm W x 16.41 ±0.083 cm D) 6.410" H x 6.400" W (front/rear of unit) x 4.750" D without clamps (16.28 cm H x 16.26 cm W x 12.07 cm D) without clamps 6.410" H x 8.67" W x 4.
Reference Information, cont’d Shipping weight Cable Cubby 200 ���������������� Cable Cubby 300S ������������� Cable Cubby 300C ������������� Cable Cubby 600 ��������������� Cable Cubby 800 ��������������� Vibration ���������������������������������������� 4 lbs (2 kg) 8 lbs (4 kg) 8 lbs (4 kg) 12 lbs (6 kg) 15 lbs (7 kg) ISTA 1A in carton (International Safe Transit Association) Listings, certifications ������������������� UL, c-UL, CSA C/US Compliances ����������������������������������� CE Warranty ���
Reference Information, cont’d Included Parts Replacement/Modification Part Numbers The Cable Cubby includes the Cable Cubby Products manual and a selection of shelf brackets, cable pass through AAPs, grommets, and hole plugs that vary depending on the Cable Cubby model.
Reference Information, cont’d AAP shelf brackets (CC 300, 600, 800) Part number Routing Template Part Numbers The following reuseable sheet metal routing templates are recommended for installation.
Reference Information, cont’d Cut-Out Template for Extron's Cut-Out Template for Extron's Cable Cubby 200 Cable Cubby 300S 5.130" (13.0 cm) 4.394" (11.16 cm) .350" (0.90 cm) 4.625 + 0.0325" (11.75 + 0.083 cm) 3.155 + 0.0325" (8.01 + 0.083 cm) 6.470" (16.4 cm) User Access SURFACE CUT-OUT AREA = 3.155+ 0.0325" SURFACE CUT-OUT AREA = 4.625 + 0.0325" + 5.970" (11.75 cm) x 5.970 0.0325" + (15.16 0.083 cm) (15.2 cm) (8.01 + 0.083 cm) x 7.312 + 0.0325" (18.57 + 0.083 cm) 8.000" (20.32 cm) 7.312 + 0.
Reference Information, cont’d Cut-Out Template for Extron's Cut-Out Template for Extron's Cable Cubby 600 Cable Cubby 300C 6.960" (17.68 cm) 6.460 + 0.0325" (16.41 + 0.083 cm) 6.500" Dia. (16.51 cm) 6.000 + 0.0325" Dia. (15.24 + 0.083cm) 6.960" (17.68 cm) 6.460 + 0.0325" (16.41 + 0.083 cm) SURFACE CUT-OUT AREA = 6.460 + 0.0325"(16.41 + 0.083 cm) x 6.460 + 0.0325"(16.41 + 0.083 cm) SURFACE CUT-OUT AREA = 6.000 + 0.0325" Dia. (15.24 + 0.083cm) Cut surface material out along this line. 0.5" (1.
Reference Information, cont’d Cut-Out Template for Extron's Cable Cubby® Products Cable Cubby 800 8.360" (21.23 cm) 7.860 + 0.0325" (19.96 + 0.083 cm) 6.820" (17.32 cm) 6.320 + 0.0325" (16.05 + 0.083 cm) SURFACE CUT-OUT AREA = 7.860 + 0.0325"(19.96 + 0.083 cm) x 6.320 + 0.0325"(16.05 + 0.083 cm) B Appendix B Cut surface material out along this line. 0.5" (1.3 cm) Top Panel Cut-Out Radius: 0.25" (0.6 cm) User Access TEMPLATE IS NOT FULL SIZE.
Packaging for Shipment The Cable Cubby has ultra-fine machined surfaces and moving parts that make it vulnerable to damage caused by mishandling during shipment if it is improperly packaged. If, for any reason, you need to return a Cable Cubby to Extron, first contact Extron to obtain a return kit. The return kit, which reduces the chances of damage during shipment, includes a sturdy shipping carton and foam that can be fitted to each Cable Cubby model (figure B-1). 2.
Packaging for Shipment, cont’d Figure B-3 — Removing center foam 6. CC 600 and 800 only — Remove and discard the inner side foam sections of the cushion in the carton (figure B-4). If you are returning a Cable Cubby 600 model, this is the correct fit. Proceed to step 8. Figure B-4 — Removing inner side foams 7. B-4 CC 800 only — Remove and discard the outer side foam sections of the cushion in the carton (figure B-5). This is the correct fit for a Cable Cubby 800 model. Proceed to step 8.
Packaging for Shipment, cont’d 10. CC 300, 600, and 800 only — Stuff the foam section removed in step 8 into the screw clamp opening in the foam cushion in the carton. 11. CC 300, 600, and 800 only — Lower the Cable Cubby, with the top closed, into the foam cushion in the shipping carton (figure B-7). 13. CC 200 only — Lower the Cable Cubby and foam into the shipping carton. 14. Place the top foam pad, removed in step 4, on top of the Cable Cubby. 15.
