User Guide User guide

Command ASCII command
(host to processor)
Response
(processor to host)
Additional description
Output Configuration
Output scaler rate
Set output rate
EX2!*X2@RATE} RateX2!*X2@]
Select output resolution and refresh
rate.
View output rate
ERATE} X2!*X2@]
Show selected output rate.
Output polarity
Set polarity
EX2#OPOL} OpolX2#]
Set polarity for RGBHV ouput.
View polarity setting
EOPOL} X2#]
Show current output polarity.
Output sync format
Set format
EX2$OSYN} OsynX2$]
Set output sync format.
View sync setting
EOSYN} X2$]
Show current output sync format.
Scan Converter Board
Video output format
Set output format
EX7%VTPO} VtpoX7%]
Select video output format to
X7%
.
View output format
EVTPO} X7%]
View setting.
Video output standard
Set output standard
EX7^VSTD} VstdX7^]
Select video output standard to
X7^
.
View output standard
EVSTD} X7^]
View setting.
Scan converter horizontal position
Specific value
ESX1^HCTR} HctrSX1^]
Set horizontal position to
X1^
.
Increment up
ES+HCTR} HctrSX1^]
Shift image right.
Increment down
ES-HCTR} HctrSX1^]
Shift image left.
View
ESHCTR} X1^]
Horizontal position value is
X1^
.
Scan converter vertical position
Specific value
ESX1^VCTR} VctrSX1^]
Set vertical position to
X1^
.
Increment up
ES+VCTR} VctrSX1^]
Shift image down.
Increment down
ES-VCTR} VctrSX1^]
Shift image up.
View
ESVCTR} X1^]
Vertical position value is
X1^
.
NOTE: X1^ = H and V position; zero location is 2048, and limits are ± the output resolution
X2! = Scaler resolution;1 = 640x480, 2 = 800x600, 3 = 852x480, 4 = 1024x768, 5 = 1024x852,
6 = 1024x1024, 7 = 1280x768, 8 = 1280x800, 9 = 1280x1024, 10 = 1360x765,
11 = 1360x768, 12 = 1365x768, 13 = 1366x768, 14 = 1365x1024, 15 = 1440x900,
16 = 1400x1050, 17 = 1680x1050, 18 = 1600x1200, 19 = 1920x1200, 20 = 480p,
21 = 576p, 22 = 720p, 23 = 1080i, 24 = 1080p, 25 = 2048x1080, 26 = 1080p CVT
X2@ = Output refresh rate; 1 = 23.98 Hz, 2 = 24 Hz, 3 = 25 Hz, 4 = 29.97 Hz, 5 = 30 Hz, 6 = 50 Hz.
7 = 59.94 Hz, 8 = 60 Hz (default), 9 = 75 Hz
X2# = Output polarity; 0 = H-/V- (default), 1 = H-/V+, 2= H+/V-, 3 = H+/V+
X2$ = Output sync format; 0 = RGBHV (default), 1 = RGsB, 2= YUV bi-level, 3 = YUV tri-level
X7% = Scan converter output format, 0 = S-video/composite video, 1 = YUVi, 2 = RGsB
X7^ = Scan converter output standard, 0 = NTSC, 1 = PAL
Annotator • SIS Communication and Control 47