Manual

ManualsBrandsExtron Electronics ManualsComputer AccessoriesAnnotator 300

Installation

Mounting and Cabling

Step 1 — Mounting

a. Turn off or disconnect all equipment power sources.

b. Mount the Annotator 300 to a rack using the pre-installed rack ears (see

gure 1), or use an optional MBU 149 mounting kit (part number 70-222-01)

for under-the-desk mounting (see gure 2).

Step 2 — Connecting inputs

a. Connect analog video sources to the universal connector (see

above).

Compatible sources are RGB, YUV (HD or SD), RGBcvS, S-video and

composite video. Default setting for the input is auto-detect.

b. Connect a digital HDMI or DVI source to the HDMI connector (see

above).

c. Connect a DisplayPort input source to the DisplayPort connector (see

above).

Step 3 — Connecting outputs

a. Connect suitable video displays to the two HDMI connectors (see

above).

b. Connect either an Extron DTP device to this connector for transmission over

DTP (default), or connect an HDBaseT device if transmitting over HDBaseT

(see

above). Set the DIP switch to DTP or HDBaseT as applicable.

CAUTION: Risk of damage to equipment.

DO NOT connect an HDBaseT unit if using DTP transmission.

The power carried over DTP may damage the unit.

Attention: Cela risque d'endommager votre équipement.

Ne PAS connecter une unité HDBaseT si vous utilisez la transmission

DTP. L'alimentation transmise sur DTP peut endommager l'unité.

Annotator 300 • Setup Guide

The Extron Annotator 300 Annotation Graphics Processor is a scaling product that allows a presenter to draw, point, or type on video or

computer source outputs using a touch panel, mouse, or keyboard.

This set up guide allows you to easily and quickly set up and congure your Annotator 300 using step by step instructions. It covers

performing basic operations using the front panel controls and selected Simple Instruction Set (SIS

™

) commands.

NOTE: For full installation, configuration, menus, and operation details, see the Annotator 300 User Guide at www.extron.com.

Rack Ears

50/60 Hz

100-240VAC --A MAX

OVER DTP

DTP

HDBT

REMOTEOUTPUTS

INPUTS

RS-232 IR

1 1UNIVERSAL HDMI DISPLAYPORT23 HDMI 2A HDMI 2B

Tx Rx GTxRx

CONTACT

LAN

RESET

USB

RS-232

Tx Rx G

SIG

DTP OUT

LINK

HIJK

Power and video input connections Outputs and control connections

A AC power connector

B Universal analog 15-pin HD connector

C HDMI connector (HDMI/DVI inputs)

D DisplayPort connector

E HDMI connectors (2) (HDMI/DVI outputs)

RJ-45 connector (DTP or HDBaseT

output), selectable by DIP switch

5-pole captive screw connector

(for DTP RS-232 and IR insert)

USB A connectors (2)

Reset button and LED

RJ-45 LAN connector

Remote RS-232 3-pole captive

screw connector

Remote contact closure 3-pole

captive screw connector

Rear Panel Features

#8 Screw

(4) Places

Each Side

MBU 149

Mounting Bracket

Mounting Screws

(2) Places

Each Side

Figure 1. Rack Mount

Figure 2. Furniture Mount

Summary of content (4 pages)

PAGE 1
Annotator 300 • Setup Guide The Extron Annotator 300 Annotation Graphics Processor is a scaling product that allows a presenter to draw, point, or type on video or computer source outputs using a touch panel, mouse, or keyboard. This set up guide allows you to easily and quickly set up and configure your Annotator 300 using step by step instructions. It covers performing basic operations using the front panel controls and selected Simple Instruction Set (SIS™) commands.
PAGE 2
Annotator 300 • Setup Guide (Continued) Step 4 — Connecting control devices a. For RS-232 or IR control over DTP, connect to the 5-pole "Over DTP" captive screw connector (see G on page 1). b. For control through Ethernet, connect a LAN or WAN to the RJ-45 connector (see J on page 1). The default IP address is 192.168.254.254. The default subnet mask is 255.255.0.0. c. For serial RS-232 control, connect a host device to the 3-pole captive screw connector (see K on page 1).
PAGE 3
Front Panel Menu System The scaler has a menu system consisting of six submenus that can be accessed using the front panel Menu and Enter buttons. The Communications menu (View Comm Settings) is a read-only menu.
PAGE 4
Annotator 300 • Setup Guide (Continued) Input Selection — This opens a pop-up palette displaying the selectable inputs. Selecting an input button switches the display to that input. Fill — Select this when selecting rectangle or ellipse, to draw a solid shape filled with the selected color. Pointer — This changes the cursor to an extra large arrow of the currently selected color. Undo — This undoes the last 15 completed annotations or a Clear action.