User’s Guide 3G HD-SDI 101 Cable Equalizer 68-1553-01 Rev.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
安全须知 • 中文 警告 这个符号提示用户该设备用户手册中 有重要的操作和维护说明。 电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 必须使用有地线的供电系统供电。 第三条线 （地线）是安全设施，不能不用或跳过。 这个符号警告用户该设备机壳内有暴 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后 或桌面电源的电源线，或任何接到市电系统的电源线。 露的危险电压，有触电危险。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 注意 阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理 解所有安全和使用说明。 保存说明书 • 用户应保存安全说明书以备将来使 用。 遵守警告 • 用户应遵守产品和用户指南上的所有安 全和操作说明。 维护 • 所有维修必须由认证的维修人员进行。 设备内部 没有用户可以更换的零件。为避免出现触电危险不要自 己试图打开设备盖子维修该设备。 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止 机内敏感元件过热。 不要用任何东西挡住通风孔。 锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用 与厂家推荐的相同
About this Manual This manual contains information about the Extron 3G HD-SDI 101 cable equalizer, with instructions on how to mount and operate this unit. About the 3G HD-SDI 101 The Extron 3G HD-SDI 101 is a compact, economical cable equalizer, which compensates for the signal degradation that takes place when video signals are passed through long lengths of coaxial cable.
Introduction 3G HD-SDI 101 Features Power LED — The front panel LED illuminates green when power is connected. Power supply — An external 12 VDC power supply High data transfer rates — Up to 2.97 Gbps Long cable runs — Up to 500' (150 m) for SDI signals using Extron RG6 cable High quality signals — Signals at all rates are equalized to give optimum signal quality. In addition, signals at standard data rates 270 Mbps (SMPTE 259M), 1.485 Gbps (SMPTE 292M), and 2.
Mounting the 3G HD-SDI 101 The small size of this extender allows it to be mounted on a tabletop, on a rack, or under furniture. N The 3G HD-SDI 101 is designed be placed at the end of a long cable run and close to the display device. Tabletop placement Attach the four included rubber feet to the bottom of the unit and place it in any convenient location.
Installation and Operation, cont’d Rack mounting procedures The unit can be mounted in the front or rear of any of these rack systems: • RSF 123 3.5" deep 1U VersaTools® rack shelf kit (part #60-190-20) • RSB 123 3.5" deep 1U VersaTools rack shelf (part #60-604-20) • RSU 126 6" deep 1U universal rack shelf kit (part #60-190-10) • RSB 126 6" deep 1U basic rack shelf (part #60-604-10) • RSU 129 9.5" deep 1U universal rack shelf kit (part #60-190-01) • RSB 129 9.
Furniture mounting The 3G HD-SDI 101 can be mounted under furniture using optional mounting kit MBU 125 (part # 70-077-01) as follows: 1. Attach the mounting brackets to the 3G HD-SDI 101 with the provided machine screws as shown in the figure below. 2. Hold the 3G HD-SDI 101 with the attached brackets against the underside of the table or other furniture. Mark the location of the screw holes in the brackets on the mounting surface. 3. Drill 3/32" (2 mm) diameter pilot holes, 1/4" (6.
Installation and Operation, cont’d Front Panel Features 3G HD-SDI 101 1 a Power LED — The LED illuminates green when the unit is receiving power. Rear Panel Features POWER 12V 0.2A MAX 2 b c d INPUT OUTPUT 3 4 Power connector — The external 12 VDC, 2A power supply (provided) is connected to this 2-pole, orange, 3.5 mm captive screw connector. HD-SDI input — One female BNC connector accepts HD-SDI input. HD-SDI output — One female BNC connector provides HD-SDI output.
3G HD-SDI 101 Operation To operate the 3G HD-SDI 101 cable equalizer, follow these instructions: 1. Mount the 3G HD-SDI 101 in a convenient location at the end of a long cable run and close to the display device. 2. Connect the power supply (provided) to the equalizer, using the captive screw connector. Ensure the connections have the correct polarity as shown in the illustration below: Smooth POWER 12V 0.
Reference Material Specifications Video Gain.................................................. Unity Resolution....................................... 8 or 10 bits, automatic Operation Standards...................... SMPTE 259M, SMPTE 292M, SMPTE 424M, ITU-R BT.601, ITU-R BT.1120 Auto data rate lock......................... Yes Video input Number/Signal Type.................... 1 single link SDI, HD-SDI, or 3G-SDI digital component video Connectors......................................
General External power supply.................. 100 VAC to 240 VAC, 50/60 Hz, external; to 12 VDC, 2A, regulated Power input requirements............ 12 VDC, 0.2A Temperature/humidity................. Storage: -40° to +158°F (-40 to +70°C)/ 10% to 90%, noncondensing Operating: +32° to +122°F (0° to +50°C)/ 10% to 90%, noncondensing Cooling............................................ Convection, no vents Mounting Rack mount......................... Yes, with optional 1U, 9.
Reference Material, cont’d Included Parts These items are included in each order for a HD-SDI 101 3G: Included parts Replacement part number 3G HD-SDI 101 60-963-01 12 VDC, 2 A mountable desktop power supply IEC power cord (4) Rubber feet (2) Strips of Velcro Product label 33-1661-01 3G HD-SDI 101 User's Guide Accessories Accessories Part number RSU 129, 9.5" deep, rack shelf kit 60-190-01 RSB 129, 9.
Extron’s Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase.
www.extron.com Extron Electronics, USA Extron Electronics, Europe Extron Electronics, Asia Extron Electronics, Japan 1230 South Lewis Street Anaheim, CA 92805 USA 714.491.1500 Fax 714.491.1517 Beeldschermweg 6C 3821 AH Amersfoort The Netherlands +31.33.453.4040 Fax +31.33.453.4050 135 Joo Seng Road, #04-01 PM Industrial Building Singapore 368363 +65.6383.4400 Fax +65.6383.4664 Kyodo Building 16 Ichibancho Chiyoda-ku, Tokyo 102-0082 Japan +81.3.3511.7655 Fax +81.3.3511.
