Setup guide

32
XTP CrossPoint 1600 and 3200 • Remote Control
33
XTP CrossPoint 1600 and 3200 • Remote Control
Command SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional Description
Ethernet serial port insert parameters (available for inputs and outputs on an XTP CP 4i and XTP CP 4o
[XTP input and output] boards only)
Set serial port parameters
EX1&
*
X1*
,
X1(
,
X2)
,
X2!
CP
}
Cpn
X1&
•Ccp
X1*
,
X1(
,
X2)
,
X2!]
Read serial port parameters
EX1&
CP
} X1*
,
X1(
,
X2)
,
X2!]
Congure current port timeout
E
0*
X2@
TC
}
Pti0*
X2@]
Read current port timeout
E
0TC
} X2@]
Congure global IP port timeout
E
1*
X2@
TC
}
Pti1*
X2@]
Read global IP port timeout
E
1TC
} X2@]
Set UART start point
EX2#
MD
}
Pmd
X2#]
Sets the initial (lowest) port number for the range of
numbers assigned to the serial port and UARTs.
Read UART start point
E
MD
} X2#]
Command SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional Description
View video and audio mutes
View output mutes
E
VM
}
X2$
1
X2$
2
...
X2$
n
]
Each
X2$
response is the mute status of an output, starting
from output 1. n = either 16 or 32.
Example :
(XTP CrossPoint 3200)
E
VM
}
Audio is muted on outputs 2 and 3, video on output 5,
and video and audio on output 26. All other outputs are
unmuted.
Mut02201000000000000000000002000000
]
List Digital Sync Validation Processing (DSVP)
List sync of all inputs
0LS
X2%
1
X2%
2
X2%
3
...
X2%
n
]
16 or 32 (
n
)
X2%
s; each is the signal status of an input,
starting from input 1.
Example
(XTP CrossPoint 3200):
0LS
Input:
Response Status:
no input detected
input detected
1 2345
6
732
0 0 0 1 1 1 0 . . . 0
Lock (Executive) modes
NOTE: See Setting the front panel locks (executive modes) on page 18 for more information on the Lock modes.
Lock all front panel functions
1X
Exe1
]
Enable Lock mode 1.
Lock advanced front panel
functions
2X
Exe2
]
Enable Lock mode 2.
Unlock all front panel functions
0X
Exe0
]
Enable Lock mode 0.
View lock status
X
X2^]
NOTE: X1& = Port number 03 — 36 = UARTs Input UARTs 1 — 32 = 03 — 34 Output UARTs 1 — 32 = 35 — 66
X1* = Baud rate 9600 (default), 19200, 38400, 115200
X1( = Parity odd, even, none, mark, space (only the rst letter is required) (default = n)
X2) = Data bits 7, 8 (default)
X2! = Stop bits 1 (default), 2
X2@ = Port timeout (10-sec. increments) 1 (= 10 seconds) - 65000 (default is 30 = 300 seconds = 5 minutes)
X2# = UART starting point The starting point (X2#) is the rear panel RS-232/RS-422 port.
The next position (X2#
+1
) is not used.
X2#
+2
through X2#
+17
(XTP CrossPoint 1600) or X2#
+33
(XTP CrossPoint 3200) are XTP inputs.
X2#
+34
through X2#
+49
(XTP CrossPoint 1600) or X2#
+65
(XTP CrossPoint 3200) are XTP outputs.
Default values: 1999 = Rear panel remote RS-232/RS-422 port
2000 is unused
2001 through 2016 (XTP CrossPoint 1600) = Input 1 through 16
2001 through 2032 (XTP CrossPoint 3200) = Input 1 through 32
2033 through 2048 (XTP CrossPoint 1600) = Output 1 through 16
2033 through 2064 (XTP CrossPoint 3200) = Output 1 through 32
NOTE:
X2$
= Video and audio mute status 0 = no mutes 2 = audio mute
1 = video mute 3 = video and audio mute
X2%
= Signal detection status 0 = no input connected 1 = input connected
X2^
= Lock mode 0 = lock mode 0 (unlocked) 1 = lock mode 1 2 = lock mode 2 (default)