Setup guide

30
XTP CrossPoint 1600 and 3200 • Remote Control
31
XTP CrossPoint 1600 and 3200 • Remote Control
Command SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional Description
Audio output volume
Set the volume to a specic value
X@
*
X1%
V Out
X@
•Vol
X1%]
Example:
1*50v
Out01•Vol50
]
Set output 1 volume to 79%.
Increment volume
X@
+V Out
X@
•Vol
X1%]
Increase volume by 1 step.
Example:
1+V
Out01•Vol51
]
Decrement volume
X@
–V Out
X@
•Vol
X1%]
Decrease volume by 1 step.
Read output volume
X@
V
X1%]
Audio mutes
Audio mute, HDMI
X@
*1Z Amt
X@
*1
]
Mute output
X@
HDMI (embedded digital audio off).
Audio mute, analog
X@
*2Z Amt
X@
*2
]
Mute output
X@
analog (analog audio off).
Audio mute, both
X@
*3Z Amt
X@
*3
]
Mute all output
X@
audio (HDMI and analog audio off).
Audio unmute
X@
*0Z Amt
X@
*0
]
Unmute output
X@
(HDMI and analog audio on).
Read audio mute
X@
Z
X1)]
1 = mute on, 0 = mute off.
Global audio mute, HDMI
1*Z
Amt1
]
Mute all embedded digital audio outputs.
Global audio mute, analog
2*Z
Amt2
]
Mute all analog audio outputs.
Global audio mute, both
3*Z
Amt3
]
Mute all embedded digital and analog audio outputs.
Global audio unmute
0*Z
Amt0
]
Unmute all audio outputs.
NOTE: • = Space
X@
= Output number 01 – 16 or 32
X1)
= Mute 0 = off (unmuted) 2 = analog on (analog muted)
1 = HDMI on (HDMI muted) 3 = HDMI and analog on (both muted)
X1%
= Volume adjustment range 0 – 64 (1 dB/step except for 0-to-1, which is 22 dB) (default = 64 [0 dB])
Command SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional Description
Captive screw and Ethernet serial port insertion enables (available for inputs and outputs on an XTP CP 4i and XTP CP 4o
[XTP input and output] boards only)
Enable an input captive screw
serial port insertion
E
I
X!
*0LRPT
}
LrptI
X!
*0
]
Enable the captive screw serial port insert on input
X!
. This
disables the Ethernet RS-232 insert.
Enable an input Ethernet serial port
insertion
E
I
X!
*1LRPT
}
LrptI
X!
*1
]
Enable the Ethernet serial port insert on input
X!
. This
disables the captive screw serial port insert.
Set all RS-232 input insertions
E
I*
X1^
*LRPT
}
LrptI00*
X1^]
View input insertion
E
I
X!
LRPT
} X1^]
View all input insertions
E
ILRPT
} X1^
1
X1^
2
X1^
3
...
X1^
n
]
One
X1^
for each installed input, starting at input 1. Inputs
that are not on an XTP CP 4i board report as 0.
Enable an output captive screw
serial port insertion
E
O
X@
*0LRPT
}
LrptO
X@
*0
]
Enable the captive screw serial port insert on output
X@
.
This disables the Ethernet serial port insert.
Enable an output Ethernet serial
port insertion
E
O
X@
*1LRPT
}
LrptO
X@
*1
]
Enable the Ethernet serial port insert on output
X@
. This
disables the captive screw serial port insert.
Set all RS-232 output insertions
E
O*
X1^
*LRPT
}
LrptO00*
X1^]
View RS-232 output insertion
E
O
X@
LRPT
} X1^]
View all output insertions
E
OLRPT
} X1^
1
X1^
2
X1^
3
...
X1^
n
]
One
X1^
for each installed output, starting at output 1.
Outputs that are not on an XTP CP 4o board report as 0.
NOTE: X! = Input number 01 – 16 or 32
X@ = Output number 01 – 16 or 32
X1^ = Captive screw or UART 0 = Captive screw RS-232 insert (default) 1 = Ethernet RS-232 insert (UART)