User guide

Command and Response Table for SIS Commands (continued)
Command SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
Reclocking
NOTES:
• Laser board reclockers are set on a per SFP basis. If an SFP is reclocked, the corresponding input and output reclockers reclock at
the same rate.
• HD-SDI reclockers are set on a per output basis only.
Set output reclocker
X$
*
X%
= Rte
X$
*
X%]
Set the rate for reclocker
X$
to
X%
.
Example:
8*00=
Rte08*00
]
Set the rate for reclocker 8 to auto.
Read reclocker status
X$
=
X%]
Show current rate status for reclocker
X$
.
Laser controls
Enable individual laser
driver
EX@
*1FIBR
}
Fibr
X@
*1
]
Enable the laser for output
X@
. The laser lights
so long as power is applied.
Disable individual laser driver
EX@
*0FIBR
}
Fibr
X@
*0
]
Disable the laser for output
X@
. The laser is off.
Set individual output laser
driver to automatic
EX@
*2FIBR
}
Fibr
X@
*2
]
Set the laser driver for output
X@
to automatic.
The laser lights when a tie is made to output
X@
, but is off when no tie is made to output
X@
or the output is muted.
Read status of all laser
drivers
E
FIBR
} X^
1
X^
2
X^
3
X^
4
...
X^
n
]
List the laser driver status of all installed outputs.
n is the highest numbered output for your switcher.
Global laser enable
E
1*FIBR
}
Fibr1]
Enable all output laser drivers.
NOTE: If your switcher has any BNC 3G/HD/SD-SDI boards installed, the global commands are not available. The switcher returns E14.
Global laser disable
E
0*FIBR
}
Fibr0]
Disable all output laser drivers.
Global laser automatic
E
2*FIBR
}
Fibr2]
Set all output laser drivers to automatic.
Save, recall, and directly write presets
NOTES:
• If you try to recall a preset that is not saved, the matrix switcher responds with the error code E11.
• The following characters are invalid or not recommended in preset names: + - , ` @ = [ ] { } ‘ “ ; : | \ and ?.
Save current configuration
as a global preset
X&
, Spr
X&]
Command character is a comma.
Example:
9,
Spr9
]
Save current ties as preset 9.
Recall a global preset
X&
. Rpr
X&]
Command character is a period.
Example:
5.
Rpr05
]
Recall preset 5, to become the current configuration.
Direct write process —
NOTE: The direct write of a global preset should always be preceded by a clear global preset ties command of that same preset number.
In a directly-written preset, the tied input of each output position (or no tied input) remains unchanged unless overwritten or cleared.
If you do not clear the ties in a global preset number before you directly write a global preset to that number, ties that are part of the
previous version of the specified preset with the same number can unexpectedly become part of the newly-created preset.
Clear ties of a global preset
E
+
X&
P0*!
}
Spr
X&]
Clear all ties in preset
X&
.
Directly write a global
preset
E
+
X&
P
X!
*
X@
!
X!
*
X@
%
X!
*
X@
$ ...
X!
*
X@
%
}
Enter as many ties as are valid for this
configuration. The
! tie, & tie, and % tie
commands are all valid
Spr
X&]
Example:
E
+27P0*!
}
Spr27
]
Clear all ties in preset 27.
Esc
+27P12*5!10*09%3*2!3*8&
Brackets are shown to separate ties for clarity
only. Create global preset 27, which ties
input 12 to output 5, input 10 to output 9, input
3 to output 2, and input 3 to output 8.
Spr27
]
NOTE: X! = Input number 000 – (maximum number of inputs for your configuration) (000 = untied)
X@ = Output number 001 – (maximum number of outputs for your configuration)
X% = Output reclocking rate 00 = Bypass mode
01 = Automatic mode (HDSDI boards only) 03 = 2.125 Gbps (laser boards only)
02 = 1.250 Gbps (laser boards only) 04 = 4.250 Gbps (laser boards only)
X^ = Laser control 0 = disable 1 = enable (default) 2 = automatic
X& = Global preset # 00 – 64
X$ = SFP or reclockable output 000 – 144 or 320 (FOX Matrix 320x) (000 = global [SFP only])
FOX Matrix 320x and FOX Matrix 14400 • Programming Guide
26