Setup guide

ANAHEIM, CA
RESET
RS232/RS422
REMOTE
LAN
ACT
LINK
100-240V
50/60Hz
1.2A MAX.
100-240V
50/60Hz
1.2A MAX.
REDUNDANT
PRIMARY
PRIMARY POWER SUPPLY
DISCONNECT BOTH POWER
CORDS BEFORE SERVICING
REDUNDANT POWER SUPPLY
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
1 - 16
17 - 32
33 - 48
49 - 64
65 - 80
81 - 96
97 - 112
113 - 128
129 - 144
FAN ASSIMBLY
FAN ASSIMBLY
Align with
Plastic Guides
Knurled
Knobs
Power
LED
Removing and Installing a Fan
The FOX.Matrix.14400.has.two.fan.modules.and.the FOX.Matrix.320x.
has.four.fan.modules..The fan.modules.for each.model.are identical.
and.hot-swappable..If.a.fan.fails,.it.should.be replaced.at.the earliest.
opportunity.
NOTES:. •. Fans.are not.interchangeable between.models..
• The fans.modules.are hot-swappable..Either.fan.can.
be removed.or.installed.without.powering.down.the
switcher.
1. Remove and.retain.the two.screws.that.secure the row.
identification.plate (identifying.rows.1.through.80,.rows.81.
through.144,.rows.81.through.160,.rows.161.through.240,.or.rows.
241.through.320).to.the fan..Retain.the plate.
2.
Rotate the top.and.bottom.knurled.knobs.to.completely.loosen.
the captive screws.
3.
Gently.pull.on.the screws.to.loosen.the fan.from.the backplane.
4.
Slid
e the fan.out.of.the chassis.
5.
Orient.the fan.to.be installed.so.that.the printing.on.the back.of.
the panel.is.right-side up.
6.
Align.the flanges.on.the fan.with.the top.and.bottom.fan.guides.
(see the next.page).
7.
Gently.slide the fan.into.the enclosure until.the fan.meets.
resistance.
8.
Gently.seat.the fan.in.the backplane.
9.
Use a.screwdriver.to.tighten.the top.and.bottom.knurled.knobs/
captive screws.to.lock.the fan.in.place.
10.
Secure the row.identification.plate to.the fan.
28 FOX Matrix 320x and FOX Matrix 14400 • Maintenance and Modifications 29FOX Matrix 320x and FOX Matrix 14400 • Maintenance and Modifications