Setup guide

ManualsBrandsExtron electronics ManualsBusiness equipment14400

4. At.the PC,.access.the MS-DOS®.command.prompt,.then enter.the

arp –s.command..Type in.the desired.new.IP.address.for.the unit.

(obtained.in.step.1).and.the MAC.address.of.the unit.(from.the

rear.panel.of.the unit)..For example:.

arp –s 10.13.197.7 00-05-A6-03-69-B0.and.then.press.

{Enter}.

Aft

er.receiving.the arp -s.command,.the controller.changes.to.

the new.address.and.starts.responding.to.the ping.requests,.as.

described.in.step.5

NOTE:. You.must.ping.the FOX.matrix.switcher.as.shown.in.

step.5.for.the IP.address.change to.take place..The

response should.show.the new.IP.address,.as.shown.in.

the following.ﬁgure.

5. Execute a.ping.command.by entering.“ping”.followed.by.a.space

and.the new.IP.address.at.the command.prompt..For example:.

ping 10.13.197.7

C:\>ping 10.13.197.7

Pinging 10.13.197.7 with 32 bytes of data:

Reply from 10.13.197.7: bytes=32 time<10ms TTL=128

Ping statistics for 10.13.197.7:

Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

Approximate round trip times in milli-seconds:

Minimum = 0ms, Maximum = 0ms, Average = 0ms

NOTE:. You.can.reconnect.using either.Telnet.or.a.Web.

browser.to.verify.that.the update was.successful.

6. After.verifying.that.the IP.address.change was.successful, enter.

and.issue the “arp.–d”.command.at.the DOS.prompt..For example:

arp –d

 10.13.197.7.removes.10.13.197.7.from.the ARP.table

or.

arp –d*.removes.all.static.IP.addresses.from.the ARP.table.

Loading the Start-up Page

NOTES:. •. If.your.Ethernet.connection.to.the matrix.switcher.

is.unstable,.try.turning.off.the proxy.server.in.your.

Web.browser..In.Microsoft.Internet.Explorer,.click.

Tools.>.Internet Options.>.Connections.>.LAN

Settings,.uncheck.the Use a proxy server....

box,.and.then.click.OK.

. •. For.details.on.operating.the switcher.via.HTML.

pages,.refer.to.the "HTML.Operation".section.in.the

FOX Matrix 320x and FOX Matrix 14400 User Guide.

1. Start.the Web.browser.program.

Click.in.the Address.ﬁeld.

Enter.the Matrix.IP.address.in.the Address.ﬁeld.

NOTE:. 192.168.254.254.is.the factory-speciﬁed.default.value

for.this.ﬁeld.

4. Press.the keyboard.Enter.key..The switcher.checks.to.see if.it.is.

password-protected.

If the switcher is not password-protected,

.it.checks.and.

downloads.the HTML.start-up.page..The switcher.is.ready.for.

operation.via.HTML.remote control.

If the switcher is passwor

d-protected,.it.downloads.the Enter.

Network.Password.page.

NOTE:. A.User.name entry.is.not.required.

5. Enter.the appropriate administrator.or.user.password.in.the

Password.ﬁeld.and.click.OK.

The switcher.downloads.the HTML.start-up.page..The switcher.is.

ready.for.operation.via.HTML.remote control.

22 FOX Matrix 320x and FOX Matrix 14400 • Remote Control

23FOX Matrix 320x and FOX Matrix 14400 • Remote Control