User Guide

ManualsBrandsExtron electronic ManualsOtherMMX 32 VGA MTP

Sleeve ( )

Ring (R)

Tip (L)

3.5 mm Stereo Plug Connector

(unbalanced)

REMOTE

RS-232

+5V

1 2 3

Tx Rx

CONTACT

Output 1 control

Output 2 control

RS-232

connection

MMX 32 VGA MTP • Setup Guide

INPUT 2

INPUT 1

AUDIO

OUTPUT 1

AUDIO

INPUT 3

AUDIO

REMOTE

AUDIO

MMX 32 VGA MTP

OUTPUT 1

213

OUTPUT 2

213

RS-232

+5V

POWER

12V

0.5A MAX

1 2 3

CONTACT

Tx Rx

SYNC - TRI

PRE PEAK - ON

OUTPUT 2

RGB/AUDIO

This guide provides basic instructions for an experienced installer to set up and operate

the Extron

MMX 32 VGA MTP mini matrix switcher. The MMX 32 VGA MTP is a compact,

three-input, two- output matrix switcher suitable for small installations or portable

systems.

NOTE: For full installation and operating details, refer to the MMX 32 VGA MTP User

Guide, available online at www.extron.com.

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the MMX 32 VGA MTP as

required (rack, furniture, or tabletop mounted).

Step 2 — Connect Inputs

Connect up to three video sources (RGBHV, RGBS, RGsB, RsGsBs,

component video, S-video or composite video) to the female

15-HD connectors, inputs 1-3.

Connect audio sources to the 3.5 mm stereo jacks and wire the

audio connectors as shown at right.

Step 3 — Connect Outputs

Attach the applicable output cables (video, audio, and video and

audio) as below:

a. Output 1 Video — Connect a display device to this female 15-pin HD connector.

b. Output 1 Audio — Connect speakers to this 3.5 mm stereo jack.

c. Output 2 Audio/Video (RGB) — Connect an MTP U R series or other MTP receiver to this

RJ-45 UTP connector.

Wire the connector as shown on the next page.

Connect a projector or other RGB video output device to the receiver, and connect speakers

for summed (L and R) mono audio output.

d. Output 2 Audio — Connect speakers to this 5-pole, 3.5 mm captive screw connector for

balanced/unbalanced audio and wire connector for dual mono output as shown below.

Unbalanced Output Balanced Output

Do not tin the wires!

Tip

NO GROUND HERE

Tip

Sleeves

Tip

Ring

Tip

Ring

CAUTION: For unbalanced audio, connect both sleeves to the center

(ground) contact. DO NOT connect the sleeves to the

negative (-) contacts.

Step 4 — Remote Connections

a. Contact closure connectors — Connect an Extron

MMX 32 AAP or MMX 32 MAAP contact closure

remote control panel to these two 5-pole captive screw

connectors to provide control for outputs 1 and 2.

Connect the 5 V and Gnd (-) 2-pole captive screw

connector on the AAP or MAAP to either of these

connectors.

NOTE: For instructions on connecting the the MMX 32 AAP or MMX 32 MAAP to the

switcher, refer to page 22 of the MMX 32 VGA MTP User Guide, or refer to the

MMX 32 AAP/MAAP Installation Guide.

b. RS-232 connector — Connect an RS-232 control module to this 3-pole captive screw

connector (see image above) to allow remote control using the Extron Simple Instruction

Set

™

(SIS

™

) or the Extron Universal Switcher Control Program.

NOTE: For full SIS commands and details of the Universal Switcher Control Program,

refer to the MMX 32 VGA MTP User Guide.

568 A

Wire color

568 B

Wire color Signal

1 White-green White-orange Red+/V. sync+

2 Green Orange Red-/V. sync-

3 White-orange White-green Mono audio+

4 Blue Blue Green+

5 White-blue White-blue Green-

6 Orange Green Mono audio-

7 White-brown White-brown Blue+/H. sync+

8 Brown Brown Blue-/H. sync-

NOTE: If you are using Enhanced Skew-Free™

A/V cable, use the TIA/EIA T568A standard

only.

Insert Tw isted

Pair Wires

Pins:

12345678

RJ-45 Connector

Summary of content (4 pages)

PAGE 1
MMX 32 VGA MTP • Setup Guide RJ-45 Connector Pins: 12345678 OUTPUT 1 1 OUTPUT 2 2 3 1 2 3 MMX 32 VGA MTP AUDIO INPUT 3 OUTPUT 2 AUDIO 1 1 AUDIO L R 2 3 +5V CONTACT RGB/AUDIO POWER 12V 0.5A MAX REMOTE SYNC - TRI PRE PEAK - ON INPUT 1 Insert Twisted Pair Wires RS-232 2 AUDIO INPUT 2 AUDIO OUTPUT 1 Tx Rx This guide provides basic instructions for an experienced installer to set up and operate the Extron® MMX 32 VGA MTP mini matrix switcher.
PAGE 2
MMX 32 VGA MTP • Setup Guide (Continued) Front Panel Operation Step 5 — Power Plug the included external 12 VDC power supply into the 2-pole captive screw connector. Wire the connector as shown at right. 3/16” (5 mm) Max. Outputs 1 and 2 — For each output press the button for the desired input (1, 2 or 3). The LED for that input lights. Smooth Ridges A A NOTE: When power is applied, the LEDs light sequentially from left to right.
PAGE 3
MMX 32 VGA MTP • Setup Guide (Continued) = Output number 1 or 2 = Mute/lock 0 = off/unlocked, 1 = on/locked = Controller software version number to second decimal place = Audio/Video mute status 0 = no mute, 2 = audio mute 1 = video mute, 3 = video and audio mute Show lock status (0 = unlocked/1 = locked) Unlock front panel. Exe0] X(] Lock front panel. Output X# is tied to input X@ video. Output X# is tied to input X@ audio. Output X# mute status is X2) Mute audio output X#.
PAGE 4
Output 1 audio is tied to input 2 audio. Output mute X2) (0 = no mute, 1 = video mute, 2 = audio mute, 3 = video and audio mute). Output 2 video is tied to input 3 video. Clear all ties and unmute audio and video. Unmute all. xx-xxx-xx] X1(] a b c NOTE: a Input 1 supplies video and audio for output 1. b Input 2 supplies video and audio for output 2. c Output 1 does not mute video or audio. d Output 2 does not mute video or audio. • The matrix switcher supports the 2-digit numeric format (01*02).