Quick Reference Guide

ManualsBrandsExtreme Networks ManualsComputers & AccessoriesPremium Stackable Edge/Aggregation Switch Platform

X465 Series Switches Quick

Reference

Follow these steps to get your switch up and running.

For complete installation instructions see the ExtremeSwitching:

Hardware Installation Guide at www.extremenetworks.com/

documentation

Tools You’ll Need

• Appropriate grounded power receptacles

located within 1.8 m (6 ft.)

• A readily accessible device for disconnecting

power, such as a breaker or master switch

• Network cabling within reach

• At least of 7.6 cm (3.0 in.) on all sides, for

proper ventilation

• Temperature between 0°C (32°F) and 50°C

(122°F) with fluctuations of less than 10°C

(18°F) per hour

If the switch appears to be damaged, contact Extreme Networks. See

“Getting Help” for more information.

Extreme Networks does not include power input cords with this product.

To purchase the correct power cord for your country, refer to

www.extremenetworks.com/product/powercords/. This page lists

details for purchasing a power cord from Extreme Networks or from

your local supplier.

1 #2 Phillips screwdriver

(magnetic screwdriver recommended)

3 ESD-protective wrist strap

2 Flat-head screwdriver

Prepare the Site

The installation site must meet the following requirements:

Unpack the Box

Remove the packing material. Break the tape seal on the

non-conductive bag and remove the switch.

1 Four-post rack mount kit 2 Switch

There are several options for mounting the switch in a rack: Two options

are described here. For details about all of the options, see the Hardware

Installation Guide.

Four-Post Mount, Front Mount

This procedure uses the four-post mounting kit (XN-4P-RKMT-001),

which is included with your switch.

1 Attach a front bracket to one side of the switch, screwing it into the

holes so that the flange (ear) is flush with the front of the switch.

2 Attach the other front bracket to the other side.

3 Attach the extension brackets to both sides of the switch, using the

screws provided.

4 Attach the front brackets to the front rack posts, using the screws

provided.

5 Slide the rear brackets into the extension brackets on both sides, and

adjust them to the rack depth as shown.

6 Attach the rear brackets to the rear rack posts, using the screws

provided.

Two-Post, Mid-Mount

This procedure uses the two-post mounting kit (XN-2P-RMKIT-001),

which accommodates rack posts 3 inches or 6 inches wide and which

can be ordered separately.

1 Attach a front bracket to one side of the switch, screwing it into the

holes so that the flange (ear) is near the middle of the switch.

2 Attach the other front bracket to the other side.

3 Attach the front brackets to the front rack posts, using the screws

provided.

4 Attach the rear brackets to the rack posts, using the screws provided.

Select the right bracket length such that the rear end of the bracket is

flush with the rear of the switch,

5 Attach both rear brackets to the side of the switch, as shown.

To install a VIM5 module:

1 Attach the ESD wrist strap to your wrist and connect the metal end

to an appropriate ground point on the rack.

2 Ensure that the switch is completely powered down.

3 Remove the cover plate from the VIM slot (#2 Phillips screwdriver

required).

4 Remove the VIM5 module from its packaging.

5 Carefully slide the VIM5 module into the slot until it is firmly in place.

6 Secure the VIM5 module using the screws provided.

To install a transceiver:

1 Attach the ESD wrist strap to your wrist and connect the metal end

to an appropriate ground point on the rack.

2 Remove the transceiver from its packaging.

3 If applicable, remove the protective dust cover from the connector.

4 Hold the transceiver so that the connector will seat properly.

5 Carefully align the transceiver with the port slot.

6 Push the transceiver into the port slot until it clicks into place.

Install the Switch

You can install any X465 Series switch in a standard 19-inch

equipment rack.

Note: It is recommended to install the long rack ear in position -4 or

-5. Do not install the long rack ear in position -2 or -3, as it will block

the air openings.

Install VIMs, Transceivers, and SSDs

(Optional) Versatile Interface Modules (VIMs) provide

dedicated high-speed ports. Your X465 Series switch

accommodates one VIM5 module, using a slot on the front

of the switch.

Transceivers send and receive data over optical fiber rather

than through electrical wires. Insert transceivers into any of

the switch’s data ports.

(Optional) Solid-state drives (SSDs) provide modular

storage support. Your X465 Series switch accommodates

one SSD module using a reserved slot on the rear of the

switch, and is supported on EXOS release 30.3 and later.

See ExtremeSwitching: Hardware Installation Guide for

details on compatible switches and SSD modules.

VIMs, transceivers, and SSDs are ordered separately.

Warning: To prevent damage to the switch or VIM, the switch

must be powered OFF when removing or installing VIMs or SSD

modules.

Note: Transceivers are Class 1 or Class 1M laser devices.

To install an SSD module:

1 Attach the ESD wrist strap to your wrist and connect the metal end

to an appropriate ground point on the rack.

2 Ensure that the switch is completely powered down.

3 Remove the cover plate from the SSD slot (#2 Phillips screwdriver

required).

4 Remove the SSD module from its packaging.

5 Carefully slide the SSD module into the slot on the rear panel until it is

firmly in place.

6 Secure the SSD module using the screws provided.

Connecting to the Primary Power Source

To attach your X465 Series switch to a power source, do the following:

1 Connect the AC power cord to the AC power input socket on the

power supply and an AC power outlet.

2 When power is connected, verify that the switch’s PWR LED turns

green. If the PWR LED does not turn green, refer to the Hardware

Installation Guide for troubleshooting information.

Operating Conditions

Operating Temperature:

0°C (32°F) to 50°C (122°F)

Temperature restrictions apply for some models at high altitudes.

See Hardware Installation Guide for details.

Storage Temperature:

-40°C to 70°C (-40°F to 158°F)

Operating Relative Humidity:

5% to 95% (non-condensing)

Safety Notices

Connect Power

X465 Series switches run on AC power.

Connect the switch to a primary power source.

Note: Installing the system as described in this guide meets the

protective earth grounding requirements of the National

Electrical Code (NEC), UL/CSA/IEC/EN 60950-1 standards.

However, in some cases, it may be necessary to use an

alternative grounding method. In these cases, a 14 AWG wire can

be connected between the grounding lug on the chassis and a

nearby building ground point.

Update and Configure

the Switch

To connect to the network, upgrade the operating-system

software to the appropriate version, and configure the

switch for use, follow the steps in

www.extrconfig.com/exos.

Electrical Hazard: Only qualified personnel should perform installation

procedures.

Risques d’électrocution: Seul un personnel qualifié doit effectuer les

procédures d'installation.

Warning: Extreme Networks power supplies do not have switches for turning

the unit on and off. Before servicing, disconnect all power cords to remove

power from the device. Make sure that these connections are easily accessible.

Avertissement: Extreme Networks alimentations ne sont pas des interrupteurs

pour allumer l'appareil et en dehors. Avant l'entretien, débranchez tous les

cordons d'alimentation pour couper l'alimentation de l'appareil. Assurez-vous

que ces connexions sont facilement accessibles.

Warning: A dedicated Listed circuit breaker rated at 15A is to be used for each

power supply connection.

Avertissement: Un disjoncteur cotée dédiée évalué à 15A doit être utilisée pour

chaque connexion d'alimentation.

Warning: Before mounting the device, ensure that the rack can support it

without compromising stability. Otherwise, personal injury and/or equipment

damage may result.

Warning: Follow appropriate ESD procedures when unpacking and handling

the switch. These include unpacking the switch in an ESD-safe environment

and wearing appropriate ESD protective gear, such as ESD-safe footwear and

ESD wrist straps where appropriate.

Warning: This unit must be installed indoors. The unit, AC power adapter, and

its cables are not designed for outdoor use.

Warning: Use of controls or adjustments or performance of procedures other

than those specified herein may result in hazardous radiation exposure.

Warning: Do not use optical instruments to view the laser output. The use of

optical instruments to view laser output increases eye hazard. Use only

UL/CSA, IEC/EN60825-1/-2 recognized pluggable modules.

Avertissement: Ne pas utiliser d'instruments optiques pour voir la sortie du

laser. L'utilisation de instruments optiques pour afficher la sortie laser

augmente les risques oculaires. Utilisez uniquement UL/CSA,

IEC/EN60825-1 /-2 reconnu modules enfichables.

Hardware Components

Figure 1 X465 Series Switch: Front Panel (48-port model shown)

Figure 2 X465 Series Switch: Rear Panel

For component details, see the Hardware Installation Guide.

Interfaces

Each X465 Series switch includes a USB micro B console port,

an RJ-45 management port, an RJ-45 console port, 2 stacking ports,

2 USB A ports for connecting to memory, and 1 unpopulated VIM5 slot.

Each switch also includes an EXOS Advanced Edge license.

Additional interfaces include:

Power Supply and Fan Options

Note: XN-ACPWR-xxx-FB power supply units cannot be used with 10941,

10951, 10953, or XN-ACPWR-2000W-F power supplies on the same switch.

Available VIM5 Modules

Available SSD Module

Available Rack-Mount Kits

1 Mode Button and System LEDs 4 Stacking ports

2 USB micro B console port 5 Access Ports

3 USB A ports

VIM slot, shown with VIM installed

Grounding lug 4 Fan modules

RJ-45 console and management ports

Power supplies

SSD slot (reserved)

X465-48T 48 10/100/1000Mb full/half duplex MACsec capable

ports, 3 fan modules, 2 unpopulated PSU slots

X465-48P 48 10/100/1000Mb full/half duplex MACsec capable

ports with 802.3at Type 2 PoE (30 W), 3 fan modules,

2 unpopulated PSU slots

X465-48W 48 10/100/1000Mb full/half duplex MACsec capable

ports with 802.3bt Type 4 PoE (90 W), 3 fan modules,

2 unpopulated PSU slots

X465-24MU 24 100Mb/1/2.5/5Gb ports with 802.3bt Type 3 PoE

(60 W), 2 fan modules, 2 unpopulated PSU slots

X465-24MU-24W 24 100Mb/1/2.5/5Gb ports with 802.3bt Type 3 PoE

(60 W) and 24 10/100/1000Mb full/half duplex MACsec

capable ports with 802.3bt Type 4 PoE (90 W), 3 fan

modules, 2 unpopulated PSU slots

X465-24W 24 10/100/1000Mb full/half duplex MACsec capable

ports with 802.3bt Type 4 PoE (90W), 2 fan modules,

2 unpopulated PSU slots

X465-24S 24 100Mb/1Gbps SFP ports, 3 fan modules,

2 unpopulated PSU slots

X465-24XE 24 1/10GbE SFP+ MACsec and LRM capable ports, 3

fan modules, 2 unpopulated PSU slots

X465i-48W 48 10/100/1000Mb full/half duplex MACsec capable

ports with 802.3bt Type 4 PoE (90 W), 3 fan modules,

2 unpopulated PSU slots

350W AC power supply

(10953 & XN-ACPWR-

350W-FB)

Compatible with X465-48T, X465-24S, and X465-

24XE

Front-to-back airflow

715W AC PoE power supply

(10951 & XN-ACPWR-715W-

FB)

Compatible with X465-48P, X465-48W, X465-

24MU, X465-24MU-24W, X465-24W, X465i-48W

Front-to-back airflow

1100W AC PoE power

supply

(10941 & XN-ACPWR-

1100W-FB)

Compatible with X465-48P, X465-48W, X465-

24MU, X465-24MU-24W, X465-24W, X465i-48W

Front-to-back airflow

2000W AC PoE power

supply

(XN-ACPWR-2000W-F &

XN-ACPWR-2000W-FB)

Compatible with X465-48P, X465-48W, X465-

24MU, X465-24MU-24W, X465-24W, X465i-48W

Front-to-back airflow

Spare fan module

(XN-FAN-002-F)

Spare fan module, front-to-back airflow

VIM5-4X Versatile Interface Module with 4 10GbE (SFP+) ports

VIM5-4XE Versatile Interface Module with 4 10GbE (SFP+) ports

supporting MACsec and LRM

VIM5-4YE Versatile Interface Module with 4 25GbE (SFP28) ports

supporting MACsec

VIM5-2Q Versatile Interface Module with 2 40GbE (QSFP) ports

XN-SSD-001-120 Modular 120GB SSD

XN-4P-RKMT-001 Four-post fixed rack mount kit (included)

XN-2P-RMKIT-001 Two-post fixed rack mount kit (separately orderable)

Summary of content (2 pages)

PAGE 1
X465 Series Switches Quick Reference Follow these steps to get your switch up and running. For complete installation instructions see the ExtremeSwitching: Hardware Installation Guide at www.extremenetworks.com/ documentation Tools You’ll Need 3 Install the Switch You can install any X465 Series switch in a standard 19-inch equipment rack. There are several options for mounting the switch in a rack: Two options are described here.
PAGE 2
Getting Help For additional support related to X465 Series switches or this document, contact Extreme Networks using one of the following methods: Product Documentation https://www.extremenetworks.com/documentation/ Global Technical Assistance Center (GTAC) Phone: 1-800-998-2408 (toll-free in U.S. and Canada) or +1-408-579-2826. For the support phone number in your country, visit: http://www.extremenetworks.