Admin Guide
Table Of Contents
- Contents
- Chapter 1: Introduction
- Chapter 2: New in this release
- Chapter 3: Basic administration
- Chapter 4: System startup fundamentals
- Chapter 5: Boot parameter configuration using ACLI
- Chapter 6: Run-time process management using ACLI
- Chapter 7: Chassis operations
- Chassis operations fundamentals
- Chassis operations configuration using ACLI
- Enabling jumbo frames
- Configuring port lock
- Configuring SONMP
- Viewing the topology message status
- Associating a port to a VRF instance
- Configuring an IP address for the management port
- Configuring Ethernet ports with Autonegotiation
- Enabling channelization
- Configuring serial management port dropping
- Controlling slot power
- Chassis operations configuration using EDM
- Editing system information
- Editing chassis information
- Configuring system flags
- Configuring channelization
- Configuring basic port parameters
- Viewing the boot configuration
- Configuring boot flags
- Enabling Jumbo frames
- Configuring the date and time
- Associating a port to a VRF instance
- Configuring CP Limit
- Configuring an IP address for the management port
- Editing the management port parameters
- Configuring the management port IPv6 interface parameters
- Configuring management port IPv6 addresses
- Auto reactivating the port of the SLPP shutdown
- Editing serial port parameters
- Enabling port lock
- Locking a port
- Viewing power information
- Viewing power status on VSP 8400
- Viewing fan information
- Viewing topology status information
- Viewing the topology message status
- Configuring a forced message control pattern
- Chapter 8: Hardware status using EDM
- Chapter 9: Domain Name Service
- Chapter 10: Licensing
- Chapter 11: Network Time Protocol
- Chapter 12: Secure Shell
- Chapter 13: System access
- System access fundamentals
- System access configuration using ACLI
- Enabling ACLI access levels
- Changing passwords
- Configuring an access policy
- Specifying a name for an access policy
- Allowing a network access to the switch
- Configuring access policies by MAC address
- System access security enhancements using ACLI
- Displaying the boot config flags status
- Enabling enhanced secure mode
- Creating accounts for different access levels
- Deleting accounts in enhanced secure mode
- Configuring a password for a specific user
- Returning the system to the factory defaults
- Configuring the password complexity rule
- Configuring the password length rule
- Configuring the change interval rule
- Configuring the reuse rule
- Configuring the maximum number of sessions
- Configuring the maximum age rule
- Configuring the pre- and post-notification rule
- System access configuration using EDM
- Chapter 14: ACLI show command reference
- Access, logon names, and passwords
- Basic switch configuration
- Current switch configuration
- CLI settings
- Ftp-access sessions
- Hardware information
- NTP server statistics
- Power summary
- Power information for power supplies
- System information
- System status (detailed)
- Telnet-access sessions
- Users logged on
- Port egress COS queue statistics
- CPU queue statistics
- Chapter 15: Port numbering and MAC address assignment reference
- Chapter 16: Supported standards, RFCs, and MIBs
- Glossary
Name Description
EnableFactoryDefaults Specifies whether the switch uses the factory default
settings at startup. The default value is disabled.
This flag is automatically reset to the default setting
after the CPU restarts. If you change this parameter,
you must restart the switch.
EnableDebugMode Enabling the debugmode will provide the opportunity
to allow user to enable TRACE on any port by
prompting the selection on the console during boot
up. This allows the user start trace for debugging
earlier on specified port. It only works on console
connection. By default, it is disabled.
Important:
Do not change this parameter unless directed
by Avaya.
EnableRebootOnError Activates or disables automatic reboot on a fatal
error. The default value is activated.
Important:
Do not change this parameter unless directed
by Avaya.
EnableTelnetServer Activates or disables the Telnet server service. The
default is disabled.
EnableRloginServer Activates or disables the rlogin and rsh server. The
default value is disabled.
EnableFtpServer Activates or disables the FTP server on the switch.
The default value is disabled. To enable FTP, ensure
that the TFTPD flag is disabled.
EnableTftpServer Activates or disables Trivial File Transfer Protocol
server service. The default value is disabled.
EnableSshServer Activates or disables the SSH server service. The
default value is enabled.
EnableSpbmConfigMode Enables you to configure SPB and IS-IS, but you
cannot configure PIM and IGMP either globally or on
an interface.
The boot flag is enabled by default.
EnableIpv6Mode Enable this flag to support IPv6 routes with prefix-
lengths greater than 64 bits. This flag is disabled by
default.
EnableEnhancedsecureMode Enables or disables enhanced secure mode. The
default is disabled.
Chassis operations
October 2015 Administering Avaya VSP 7200 Series and 8000 Series 92
Comments on this document? infodev@avaya.com