Admin Guide
Table Of Contents
- Contents
- Chapter 1: Introduction
- Chapter 2: New in this release
- Chapter 3: Basic administration
- Chapter 4: System startup fundamentals
- Chapter 5: Boot parameter configuration using ACLI
- Chapter 6: Run-time process management using ACLI
- Chapter 7: Chassis operations
- Chassis operations fundamentals
- Chassis operations configuration using ACLI
- Enabling jumbo frames
- Configuring port lock
- Configuring SONMP
- Viewing the topology message status
- Associating a port to a VRF instance
- Configuring an IP address for the management port
- Configuring Ethernet ports with Autonegotiation
- Enabling channelization
- Configuring serial management port dropping
- Controlling slot power
- Chassis operations configuration using EDM
- Editing system information
- Editing chassis information
- Configuring system flags
- Configuring channelization
- Configuring basic port parameters
- Viewing the boot configuration
- Configuring boot flags
- Enabling Jumbo frames
- Configuring the date and time
- Associating a port to a VRF instance
- Configuring CP Limit
- Configuring an IP address for the management port
- Editing the management port parameters
- Configuring the management port IPv6 interface parameters
- Configuring management port IPv6 addresses
- Auto reactivating the port of the SLPP shutdown
- Editing serial port parameters
- Enabling port lock
- Locking a port
- Viewing power information
- Viewing power status on VSP 8400
- Viewing fan information
- Viewing topology status information
- Viewing the topology message status
- Configuring a forced message control pattern
- Chapter 8: Hardware status using EDM
- Chapter 9: Domain Name Service
- Chapter 10: Licensing
- Chapter 11: Network Time Protocol
- Chapter 12: Secure Shell
- Chapter 13: System access
- System access fundamentals
- System access configuration using ACLI
- Enabling ACLI access levels
- Changing passwords
- Configuring an access policy
- Specifying a name for an access policy
- Allowing a network access to the switch
- Configuring access policies by MAC address
- System access security enhancements using ACLI
- Displaying the boot config flags status
- Enabling enhanced secure mode
- Creating accounts for different access levels
- Deleting accounts in enhanced secure mode
- Configuring a password for a specific user
- Returning the system to the factory defaults
- Configuring the password complexity rule
- Configuring the password length rule
- Configuring the change interval rule
- Configuring the reuse rule
- Configuring the maximum number of sessions
- Configuring the maximum age rule
- Configuring the pre- and post-notification rule
- System access configuration using EDM
- Chapter 14: ACLI show command reference
- Access, logon names, and passwords
- Basic switch configuration
- Current switch configuration
- CLI settings
- Ftp-access sessions
- Hardware information
- NTP server statistics
- Power summary
- Power information for power supplies
- System information
- System status (detailed)
- Telnet-access sessions
- Users logged on
- Port egress COS queue statistics
- CPU queue statistics
- Chapter 15: Port numbering and MAC address assignment reference
- Chapter 16: Supported standards, RFCs, and MIBs
- Glossary
Name Description
Note that the 8424XT ESM does not support the
following speeds: 10-full, 10-half, and 1000-half.
AdminDuplex Configures the administrative duplex setting for the
port.
The switch does not support half duplex.
OperDuplex Indicates the operational duplex setting for the port.
The switch does not support half duplex.
AdminSpeed Configures the administrative speed for the port.
OperSpeed Indicates the operational speed for the port.
QoSLevel Selects the Quality of Service (QoS) level for this
port. The default is level1.
DiffServ Enables the Differentiated Service feature for this
port. The default is disabled.
Layer3Trust Configures if the system should trust Layer 3 packets
coming from access links or core links only. The
default is core.
Layer2Override8021p Specifies whether Layer 2 802.1p override is
enabled (selected) or disabled (cleared) on the port.
The default is disabled (clear).
MltId Shows the MLT ID associated with this port. The
default is 0.
Locked Shows if the port is locked. The default is disabled.
UnknownMacDiscard Discards packets that have an unknown source MAC
address, and prevents other ports from sending
packets with that same MAC address as the
destination MAC address. The default is disabled.
DirectBroadcastEnable Specifies if this interface forwards direct broadcast
traffic.
OperRouting Shows the routing status of the port.
HighSecureEnable Enables or disables the high secure feature for this
port.
RmonEnable Enables or disables Remote Monitoring (RMON) on
the interface. The default is disabled.
IpsecEnable Enables or disables IP security (IPsec) on the
interface. The default is disabled.
IngressRateLimit Limits the traffic rate accepted by the specified
ingress port.
EgressRateLimitState Enables or disables egress port-based shaping to
bind the maximum rate at which traffic leaves the
port. The default is disabled.
Table continues…
Chassis operations
October 2015 Administering Avaya VSP 7200 Series and 8000 Series 90
Comments on this document? infodev@avaya.com