Admin Guide
Table Of Contents
- Contents
- Chapter 1: Introduction
- Chapter 2: New in this release
- Chapter 3: Basic administration
- Chapter 4: System startup fundamentals
- Chapter 5: Boot parameter configuration using ACLI
- Chapter 6: Run-time process management using ACLI
- Chapter 7: Chassis operations
- Chassis operations fundamentals
- Chassis operations configuration using ACLI
- Enabling jumbo frames
- Configuring port lock
- Configuring SONMP
- Viewing the topology message status
- Associating a port to a VRF instance
- Configuring an IP address for the management port
- Configuring Ethernet ports with Autonegotiation
- Enabling channelization
- Configuring serial management port dropping
- Controlling slot power
- Chassis operations configuration using EDM
- Editing system information
- Editing chassis information
- Configuring system flags
- Configuring channelization
- Configuring basic port parameters
- Viewing the boot configuration
- Configuring boot flags
- Enabling Jumbo frames
- Configuring the date and time
- Associating a port to a VRF instance
- Configuring CP Limit
- Configuring an IP address for the management port
- Editing the management port parameters
- Configuring the management port IPv6 interface parameters
- Configuring management port IPv6 addresses
- Auto reactivating the port of the SLPP shutdown
- Editing serial port parameters
- Enabling port lock
- Locking a port
- Viewing power information
- Viewing power status on VSP 8400
- Viewing fan information
- Viewing topology status information
- Viewing the topology message status
- Configuring a forced message control pattern
- Chapter 8: Hardware status using EDM
- Chapter 9: Domain Name Service
- Chapter 10: Licensing
- Chapter 11: Network Time Protocol
- Chapter 12: Secure Shell
- Chapter 13: System access
- System access fundamentals
- System access configuration using ACLI
- Enabling ACLI access levels
- Changing passwords
- Configuring an access policy
- Specifying a name for an access policy
- Allowing a network access to the switch
- Configuring access policies by MAC address
- System access security enhancements using ACLI
- Displaying the boot config flags status
- Enabling enhanced secure mode
- Creating accounts for different access levels
- Deleting accounts in enhanced secure mode
- Configuring a password for a specific user
- Returning the system to the factory defaults
- Configuring the password complexity rule
- Configuring the password length rule
- Configuring the change interval rule
- Configuring the reuse rule
- Configuring the maximum number of sessions
- Configuring the maximum age rule
- Configuring the pre- and post-notification rule
- System access configuration using EDM
- Chapter 14: ACLI show command reference
- Access, logon names, and passwords
- Basic switch configuration
- Current switch configuration
- CLI settings
- Ftp-access sessions
- Hardware information
- NTP server statistics
- Power summary
- Power information for power supplies
- System information
- System status (detailed)
- Telnet-access sessions
- Users logged on
- Port egress COS queue statistics
- CPU queue statistics
- Chapter 15: Port numbering and MAC address assignment reference
- Chapter 16: Supported standards, RFCs, and MIBs
- Glossary
Name Description
ActionGroup3 Can be the following action:
• flushIpRouteTbl—flushes IP routes from the
routing table
ActionGroup4 Can be the following action:
• softReset—resets the device without running
power-on tests
• resetConsole—resets the switch console
Result Displays a message after you click Apply.
Editing chassis information
About this task
Edit the chassis information to make changes to chassis-wide settings.
Procedure
1. In the Device Physical View tab, select the Device.
2. In the navigation tree, open the following folders: Configuration > Edit.
3. Click Chassis.
4. Click the Chassis tab.
5. Edit the necessary options.
6. Click Apply.
Chassis field descriptions
Use the data in the following table to use the Chassis tab.
Name
Description
Type Specifies the chassis type.
SerialNumber Specifies a unique chassis serial number.
HardwareRevision Specifies the current hardware revision of the device chassis.
NumSlots Specifies the number of slots available in the chassis:
• VSP 7200 Series 2 slots
• VSP 8200: 1 slot
• VSP 8400: 4 slots
NumPorts Specifies the number of ports currently installed in the chassis.
BaseMacAddr Specifies the starting point of the block of MAC addresses used
by the switch for logical and physical interfaces.
Table continues…
Chassis operations
October 2015 Administering Avaya VSP 7200 Series and 8000 Series 84
Comments on this document? infodev@avaya.com