Admin Guide
Table Of Contents
- Contents
- Chapter 1: Introduction
- Chapter 2: New in this release
- Chapter 3: Basic administration
- Chapter 4: System startup fundamentals
- Chapter 5: Boot parameter configuration using ACLI
- Chapter 6: Run-time process management using ACLI
- Chapter 7: Chassis operations
- Chassis operations fundamentals
- Chassis operations configuration using ACLI
- Enabling jumbo frames
- Configuring port lock
- Configuring SONMP
- Viewing the topology message status
- Associating a port to a VRF instance
- Configuring an IP address for the management port
- Configuring Ethernet ports with Autonegotiation
- Enabling channelization
- Configuring serial management port dropping
- Controlling slot power
- Chassis operations configuration using EDM
- Editing system information
- Editing chassis information
- Configuring system flags
- Configuring channelization
- Configuring basic port parameters
- Viewing the boot configuration
- Configuring boot flags
- Enabling Jumbo frames
- Configuring the date and time
- Associating a port to a VRF instance
- Configuring CP Limit
- Configuring an IP address for the management port
- Editing the management port parameters
- Configuring the management port IPv6 interface parameters
- Configuring management port IPv6 addresses
- Auto reactivating the port of the SLPP shutdown
- Editing serial port parameters
- Enabling port lock
- Locking a port
- Viewing power information
- Viewing power status on VSP 8400
- Viewing fan information
- Viewing topology status information
- Viewing the topology message status
- Configuring a forced message control pattern
- Chapter 8: Hardware status using EDM
- Chapter 9: Domain Name Service
- Chapter 10: Licensing
- Chapter 11: Network Time Protocol
- Chapter 12: Secure Shell
- Chapter 13: System access
- System access fundamentals
- System access configuration using ACLI
- Enabling ACLI access levels
- Changing passwords
- Configuring an access policy
- Specifying a name for an access policy
- Allowing a network access to the switch
- Configuring access policies by MAC address
- System access security enhancements using ACLI
- Displaying the boot config flags status
- Enabling enhanced secure mode
- Creating accounts for different access levels
- Deleting accounts in enhanced secure mode
- Configuring a password for a specific user
- Returning the system to the factory defaults
- Configuring the password complexity rule
- Configuring the password length rule
- Configuring the change interval rule
- Configuring the reuse rule
- Configuring the maximum number of sessions
- Configuring the maximum age rule
- Configuring the pre- and post-notification rule
- System access configuration using EDM
- Chapter 14: ACLI show command reference
- Access, logon names, and passwords
- Basic switch configuration
- Current switch configuration
- CLI settings
- Ftp-access sessions
- Hardware information
- NTP server statistics
- Power summary
- Power information for power supplies
- System information
- System status (detailed)
- Telnet-access sessions
- Users logged on
- Port egress COS queue statistics
- CPU queue statistics
- Chapter 15: Port numbering and MAC address assignment reference
- Chapter 16: Supported standards, RFCs, and MIBs
- Glossary
Serial ports interrupted due to link disconnection, power failure, or other reasons force out the user
and end the user session. Ending the user session ensures a maintenance port is not available with
an active session that can allow unauthorized use by someone other than the authenticated user,
and prevents the physical hijacking of an active session by unplugging the connected cable and
plugging in another.
By default, the feature is disabled with enhanced secure mode disabled. If enhanced secure mode
is enabled, the default is enabled.
For more information on enhanced secure mode, see
Enabling enhanced secure mode on
page 181.
Procedure
1. Enter Global Configuration mode:
enable
configure terminal
2. Configure the serial port to drop if a connection is interrupted:
sys security-console
Example
Configure the serial port to drop if a connection is interrupted:
Switch:1>enable
Switch:1#configure terminal
Switch:1(config)#sys security-console
Controlling slot power
About this task
The sys power slot command is used to control slot power on an Avaya Virtual Services
Platform 8400.
Important:
This command is only available for use with the Avaya Virtual Services Platform 8400.
Procedure
1. Enter Global Configuration mode:
enable
configure terminal
2. Configure slot power:
[no] sys power slot {slot[-slot][,...]}
Chassis operations configuration using ACLI
October 2015 Administering Avaya VSP 7200 Series and 8000 Series 81
Comments on this document? infodev@avaya.com