Admin Guide
Table Of Contents
- Contents
- Chapter 1: Introduction
- Chapter 2: New in this release
- Chapter 3: Basic administration
- Chapter 4: System startup fundamentals
- Chapter 5: Boot parameter configuration using ACLI
- Chapter 6: Run-time process management using ACLI
- Chapter 7: Chassis operations
- Chassis operations fundamentals
- Chassis operations configuration using ACLI
- Enabling jumbo frames
- Configuring port lock
- Configuring SONMP
- Viewing the topology message status
- Associating a port to a VRF instance
- Configuring an IP address for the management port
- Configuring Ethernet ports with Autonegotiation
- Enabling channelization
- Configuring serial management port dropping
- Controlling slot power
- Chassis operations configuration using EDM
- Editing system information
- Editing chassis information
- Configuring system flags
- Configuring channelization
- Configuring basic port parameters
- Viewing the boot configuration
- Configuring boot flags
- Enabling Jumbo frames
- Configuring the date and time
- Associating a port to a VRF instance
- Configuring CP Limit
- Configuring an IP address for the management port
- Editing the management port parameters
- Configuring the management port IPv6 interface parameters
- Configuring management port IPv6 addresses
- Auto reactivating the port of the SLPP shutdown
- Editing serial port parameters
- Enabling port lock
- Locking a port
- Viewing power information
- Viewing power status on VSP 8400
- Viewing fan information
- Viewing topology status information
- Viewing the topology message status
- Configuring a forced message control pattern
- Chapter 8: Hardware status using EDM
- Chapter 9: Domain Name Service
- Chapter 10: Licensing
- Chapter 11: Network Time Protocol
- Chapter 12: Secure Shell
- Chapter 13: System access
- System access fundamentals
- System access configuration using ACLI
- Enabling ACLI access levels
- Changing passwords
- Configuring an access policy
- Specifying a name for an access policy
- Allowing a network access to the switch
- Configuring access policies by MAC address
- System access security enhancements using ACLI
- Displaying the boot config flags status
- Enabling enhanced secure mode
- Creating accounts for different access levels
- Deleting accounts in enhanced secure mode
- Configuring a password for a specific user
- Returning the system to the factory defaults
- Configuring the password complexity rule
- Configuring the password length rule
- Configuring the change interval rule
- Configuring the reuse rule
- Configuring the maximum number of sessions
- Configuring the maximum age rule
- Configuring the pre- and post-notification rule
- System access configuration using EDM
- Chapter 14: ACLI show command reference
- Access, logon names, and passwords
- Basic switch configuration
- Current switch configuration
- CLI settings
- Ftp-access sessions
- Hardware information
- NTP server statistics
- Power summary
- Power information for power supplies
- System information
- System status (detailed)
- Telnet-access sessions
- Users logged on
- Port egress COS queue statistics
- CPU queue statistics
- Chapter 15: Port numbering and MAC address assignment reference
- Chapter 16: Supported standards, RFCs, and MIBs
- Glossary
Ftp-access sessions
Use the show ftp-access command to display the total sessions allowed. The syntax for this
command is as follows.
show ftp-access
The following example shows output from the show ftp-access command.
Switch:1#show ftp-access
max ipv4 sessions : 4
Hardware information
Use the show sys-info command to display system status and technical information about the
switch hardware components. The command displays several pages of information, including
general information about the system (such as location), chassis (type, serial number, and base
MAC address), temperature, power supplies, fans, cards, system errors, port locks, topology status,
and message control information. The syntax fo this command is as follows.
show sys-info [card] [fan] [led] [power] [temperature]
The following table explains parameters for this command.
Table 51: Command parameters
Parameter
Description
card
Specifies information about the device. Includes
type, serial number and assembly date.
fan
Specifies information about installed cooling ports.
led
Displays LED information in detail.
power
Specifies information about installed power supplies.
temperature
Displays temperature information.
The following example shows partial output from the show sys-info command for VSP
8284XSQ. The output for this command can be different for other VOSS switches because of
hardware differences.
Switch:1>show sys-info
General Info :
SysDescr : VSP-8284XSQ (4.2.1.0) (DEV)
SysName : Switch
SysUpTime : 0 day(s), 15:49:09
SysContact : http://support.avaya.com/
SysLocation : 211 Mt. Airy Road,Basking Ridge,NJ 07920
Chassis Info:
Chassis : 8284XSQ
Ftp-access sessions
October 2015 Administering Avaya VSP 7200 Series and 8000 Series 205
Comments on this document? infodev@avaya.com