Admin Guide
Table Of Contents
- Contents
- Chapter 1: Introduction
- Chapter 2: New in this release
- Chapter 3: Basic administration
- Chapter 4: System startup fundamentals
- Chapter 5: Boot parameter configuration using ACLI
- Chapter 6: Run-time process management using ACLI
- Chapter 7: Chassis operations
- Chassis operations fundamentals
- Chassis operations configuration using ACLI
- Enabling jumbo frames
- Configuring port lock
- Configuring SONMP
- Viewing the topology message status
- Associating a port to a VRF instance
- Configuring an IP address for the management port
- Configuring Ethernet ports with Autonegotiation
- Enabling channelization
- Configuring serial management port dropping
- Controlling slot power
- Chassis operations configuration using EDM
- Editing system information
- Editing chassis information
- Configuring system flags
- Configuring channelization
- Configuring basic port parameters
- Viewing the boot configuration
- Configuring boot flags
- Enabling Jumbo frames
- Configuring the date and time
- Associating a port to a VRF instance
- Configuring CP Limit
- Configuring an IP address for the management port
- Editing the management port parameters
- Configuring the management port IPv6 interface parameters
- Configuring management port IPv6 addresses
- Auto reactivating the port of the SLPP shutdown
- Editing serial port parameters
- Enabling port lock
- Locking a port
- Viewing power information
- Viewing power status on VSP 8400
- Viewing fan information
- Viewing topology status information
- Viewing the topology message status
- Configuring a forced message control pattern
- Chapter 8: Hardware status using EDM
- Chapter 9: Domain Name Service
- Chapter 10: Licensing
- Chapter 11: Network Time Protocol
- Chapter 12: Secure Shell
- Chapter 13: System access
- System access fundamentals
- System access configuration using ACLI
- Enabling ACLI access levels
- Changing passwords
- Configuring an access policy
- Specifying a name for an access policy
- Allowing a network access to the switch
- Configuring access policies by MAC address
- System access security enhancements using ACLI
- Displaying the boot config flags status
- Enabling enhanced secure mode
- Creating accounts for different access levels
- Deleting accounts in enhanced secure mode
- Configuring a password for a specific user
- Returning the system to the factory defaults
- Configuring the password complexity rule
- Configuring the password length rule
- Configuring the change interval rule
- Configuring the reuse rule
- Configuring the maximum number of sessions
- Configuring the maximum age rule
- Configuring the pre- and post-notification rule
- System access configuration using EDM
- Chapter 14: ACLI show command reference
- Access, logon names, and passwords
- Basic switch configuration
- Current switch configuration
- CLI settings
- Ftp-access sessions
- Hardware information
- NTP server statistics
- Power summary
- Power information for power supplies
- System information
- System status (detailed)
- Telnet-access sessions
- Users logged on
- Port egress COS queue statistics
- CPU queue statistics
- Chapter 15: Port numbering and MAC address assignment reference
- Chapter 16: Supported standards, RFCs, and MIBs
- Glossary
Name Description
with an rw access level specified for a policy ID in the
policy table is allowed rw access, and ro is denied access.
The default is false.
Enabling an access policy
About this task
Enable the access policy feature globally to control access across the switch.
You can create an access policy to control access to the switch. An access policy specifies the
hosts or networks that can access the switch through access services; for example Telnet, SNMP,
Hypertext Transfer Protocol (HTTP), and remote login (rlogin).
Procedure
1. In the Device Physical View tab, select the Device.
2. In the navigation tree, expand the following folders: Configuration > Edit.
3. Click Chassis.
4. Click the System Flags tab.
5. Select the EnableAccessPolicy check box.
6. Click Apply.
7. Click Close.
System access security enhancements using EDM
The section provides information to enable enhanced secure mode.
Enabling enhanced secure mode
Use the following procedure to enable enhanced secure mode. Enhanced secure mode is disabled
by default.
About this task
After you enable enhanced secure mode, the system can provide role-based access levels, stronger
password requirements, and stronger rules on password length, password complexity, password
change intervals, password reuse, and password maximum age use.
After you disable enhanced secure mode, the authentication, access-level, and password
requirements work similarly to any of the existing commercial releases.
System access
October 2015 Administering Avaya VSP 7200 Series and 8000 Series 200
Comments on this document? infodev@avaya.com