Admin Guide
Table Of Contents
- Contents
- Chapter 1: Introduction
- Chapter 2: New in this release
- Chapter 3: Basic administration
- Chapter 4: System startup fundamentals
- Chapter 5: Boot parameter configuration using ACLI
- Chapter 6: Run-time process management using ACLI
- Chapter 7: Chassis operations
- Chassis operations fundamentals
- Chassis operations configuration using ACLI
- Enabling jumbo frames
- Configuring port lock
- Configuring SONMP
- Viewing the topology message status
- Associating a port to a VRF instance
- Configuring an IP address for the management port
- Configuring Ethernet ports with Autonegotiation
- Enabling channelization
- Configuring serial management port dropping
- Controlling slot power
- Chassis operations configuration using EDM
- Editing system information
- Editing chassis information
- Configuring system flags
- Configuring channelization
- Configuring basic port parameters
- Viewing the boot configuration
- Configuring boot flags
- Enabling Jumbo frames
- Configuring the date and time
- Associating a port to a VRF instance
- Configuring CP Limit
- Configuring an IP address for the management port
- Editing the management port parameters
- Configuring the management port IPv6 interface parameters
- Configuring management port IPv6 addresses
- Auto reactivating the port of the SLPP shutdown
- Editing serial port parameters
- Enabling port lock
- Locking a port
- Viewing power information
- Viewing power status on VSP 8400
- Viewing fan information
- Viewing topology status information
- Viewing the topology message status
- Configuring a forced message control pattern
- Chapter 8: Hardware status using EDM
- Chapter 9: Domain Name Service
- Chapter 10: Licensing
- Chapter 11: Network Time Protocol
- Chapter 12: Secure Shell
- Chapter 13: System access
- System access fundamentals
- System access configuration using ACLI
- Enabling ACLI access levels
- Changing passwords
- Configuring an access policy
- Specifying a name for an access policy
- Allowing a network access to the switch
- Configuring access policies by MAC address
- System access security enhancements using ACLI
- Displaying the boot config flags status
- Enabling enhanced secure mode
- Creating accounts for different access levels
- Deleting accounts in enhanced secure mode
- Configuring a password for a specific user
- Returning the system to the factory defaults
- Configuring the password complexity rule
- Configuring the password length rule
- Configuring the change interval rule
- Configuring the reuse rule
- Configuring the maximum number of sessions
- Configuring the maximum age rule
- Configuring the pre- and post-notification rule
- System access configuration using EDM
- Chapter 14: ACLI show command reference
- Access, logon names, and passwords
- Basic switch configuration
- Current switch configuration
- CLI settings
- Ftp-access sessions
- Hardware information
- NTP server statistics
- Power summary
- Power information for power supplies
- System information
- System status (detailed)
- Telnet-access sessions
- Users logged on
- Port egress COS queue statistics
- CPU queue statistics
- Chapter 15: Port numbering and MAC address assignment reference
- Chapter 16: Supported standards, RFCs, and MIBs
- Glossary
Important:
If you select the AccessStrict option, you specify that a user must use an access level
identical to the one you select.
18. Click Insert.
Access Policies field descriptions
Use the data in the following table to use the Access Policies tab.
Name Description
Id Specifies the policy ID.
Name Specifies the name of the policy.
PolicyEnable Activates the access policy. The default is enabled.
Mode Indicates whether a packet with a source IP address matching
this entry is permitted to enter the device or is denied access.
The default is allow.
If you configure the access policy mode to deny, the system
checks the mode and service, and if they match the system
denies the connection. With the access policy mode configured
to deny, the system does not check AccessLevel and
AccessStrict information. If you configure the access policy
mode to allow, the system continues to check the AccessLevel
and AccessStrict information.
Service Indicates the protocol to which this entry applies. The default is
no service enabled.
Precedence Indicates the precedence of the policy expressed in a range
from 1–128. The lower the number, the higher the precedence.
The default is 10.
NetInetAddrType Indicates the source network Internet address type as one of
the following.
• any
• IPv4
• IPv6
IPv4 is expressed in the format a.b.c.d. Express IPv6 in the
format x:x:x:x:x:x:x:x.
NetInetAddress Indicates the source network Inet address (prefix/network). If
the address type is IPv4, you must enter an IPv4 address and
its mask length.You do not need to provide this information if
you select the NetInetAddrType of any. If the type is IPv6, you
must enter an IPv6 address. You do not need to provide this
information if you select the NetInetAddrType of any.
NetInetAddrPrefixLen Indicates the source network Inet address prefix-length/mask. If
the type is IPv4, you must enter an IPv4 address and mask
Table continues…
System access
October 2015 Administering Avaya VSP 7200 Series and 8000 Series 198
Comments on this document? infodev@avaya.com