Admin Guide
Table Of Contents
- Contents
- Chapter 1: Introduction
- Chapter 2: New in this release
- Chapter 3: Basic administration
- Chapter 4: System startup fundamentals
- Chapter 5: Boot parameter configuration using ACLI
- Chapter 6: Run-time process management using ACLI
- Chapter 7: Chassis operations
- Chassis operations fundamentals
- Chassis operations configuration using ACLI
- Enabling jumbo frames
- Configuring port lock
- Configuring SONMP
- Viewing the topology message status
- Associating a port to a VRF instance
- Configuring an IP address for the management port
- Configuring Ethernet ports with Autonegotiation
- Enabling channelization
- Configuring serial management port dropping
- Controlling slot power
- Chassis operations configuration using EDM
- Editing system information
- Editing chassis information
- Configuring system flags
- Configuring channelization
- Configuring basic port parameters
- Viewing the boot configuration
- Configuring boot flags
- Enabling Jumbo frames
- Configuring the date and time
- Associating a port to a VRF instance
- Configuring CP Limit
- Configuring an IP address for the management port
- Editing the management port parameters
- Configuring the management port IPv6 interface parameters
- Configuring management port IPv6 addresses
- Auto reactivating the port of the SLPP shutdown
- Editing serial port parameters
- Enabling port lock
- Locking a port
- Viewing power information
- Viewing power status on VSP 8400
- Viewing fan information
- Viewing topology status information
- Viewing the topology message status
- Configuring a forced message control pattern
- Chapter 8: Hardware status using EDM
- Chapter 9: Domain Name Service
- Chapter 10: Licensing
- Chapter 11: Network Time Protocol
- Chapter 12: Secure Shell
- Chapter 13: System access
- System access fundamentals
- System access configuration using ACLI
- Enabling ACLI access levels
- Changing passwords
- Configuring an access policy
- Specifying a name for an access policy
- Allowing a network access to the switch
- Configuring access policies by MAC address
- System access security enhancements using ACLI
- Displaying the boot config flags status
- Enabling enhanced secure mode
- Creating accounts for different access levels
- Deleting accounts in enhanced secure mode
- Configuring a password for a specific user
- Returning the system to the factory defaults
- Configuring the password complexity rule
- Configuring the password length rule
- Configuring the change interval rule
- Configuring the reuse rule
- Configuring the maximum number of sessions
- Configuring the maximum age rule
- Configuring the pre- and post-notification rule
- System access configuration using EDM
- Chapter 14: ACLI show command reference
- Access, logon names, and passwords
- Basic switch configuration
- Current switch configuration
- CLI settings
- Ftp-access sessions
- Hardware information
- NTP server statistics
- Power summary
- Power information for power supplies
- System information
- System status (detailed)
- Telnet-access sessions
- Users logged on
- Port egress COS queue statistics
- CPU queue statistics
- Chapter 15: Port numbering and MAC address assignment reference
- Chapter 16: Supported standards, RFCs, and MIBs
- Glossary
Configuring access policies by MAC address
About this task
Configure access-policies by MAC address to allow or deny local MAC addresses on the network
management port after an access policy is activated. If the source MAC does not match a
configured entry, the default action is taken. A log message is generated to record the denial of
access. For connections coming in from a different subnet, the source mac of the last hop is used in
decision making. Configure access-policies by MAC address does not perform MAC or Forwarding
Database (FDB) filtering on data ports.
Procedure
1. Enter Global Configuration mode:
enable
configure terminal
2. Add the MAC address and configure the action for the policy:
access-policy by-mac <0x00:0x00:0x00:0x00:0x00:0x00> <allow|deny>
3. Specify the action for a MAC address that does not match the policy:
access-policy by-mac action <allow|deny>
Example
Switch:1> enable
Switch:1 configure terminal
Add the MAC address:
Switch:1(config)# access-policy by-mac 00–C0–D0–86–BB-E7 allow
Variable definitions
Use the data in the following table to use the access-policy by-mac command.
Table 49: Variable definitions
Variable Value
<0x00:0x00:0x00:0x00: 0x00:0x00> Adds a MAC address to the policy. Enter the MAC address in
hexadecimal format.
<allow|deny> Specifies the action to take for the MAC address.
System access security enhancements using ACLI
The section provides information on security enhancements after you enable enhanced secure
mode.
System access
October 2015 Administering Avaya VSP 7200 Series and 8000 Series 180
Comments on this document? infodev@avaya.com